Filter
Top Products
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of
10 cm or more.
INSTRUCTIONS
GVT0242-001A[B]
0108WMKMDWJMM
©2008 Victor Company of Japan, Limited
1
2 4
Connections
Basic and Common Operations
IMPORTANT for the U.K.
DO NOT cut off the mains plug from this equipment. If
the plug fitted is not suitable for the power points in your
home or the cable is too short to reach a power point,
then obtain an appropriate safety approved extension lead
or consult your dealer.
BE SURE to replace the fuse only with an identical
approved type, as originally fitted.
If nonetheless the mains plug is cut off ensure to remove
the fuse and dispose of the plug immediately, to avoid a
possible shock hazard by inadvertent connection to the
mains supply.
If this product is not supplied fitted with a mains plug then
follow the instructions given below:
IMPORTANT:
DO NOT make any connection to the terminal which is
marked with the letter E or by the safety earth symbol or
coloured green or green-and-yellow.
The wires in the mains lead on this product are coloured in
accordance with the following code:
Blue: Neutral
Brown: Live
As these colours may not correspond with the coloured
markings identifying the terminals in your plug proceed
as follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or coloured
black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or coloured
red.
IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.
Warnings, Cautions and Others
CAUTION: (Standby/on) button!
Disconnect the mains plug to shut the power off completely
(the STANDBY lamp goes off). When installing the apparatus,
ensure that the plug is easily accessible. The (Standby/on)
button in any position does not disconnect the mains line.
• When the System is on standby, the STANDBY lamp lights
red.
• When the System is turned on, the STANDBY lamp goes
off.
The power can be remote controlled.
CAUTION:
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Supplied Accessories
After unpacking, check to be sure that you have all the
following items.
• Remote control, RM-SUXGP5R (× 1)
• Lithium coin battery CR2025 (× 1)
– The battery has been installed when shipped from the
factory.
• AM loop antenna (× 1)
• FM antenna (× 1)
If anything is missing, consult your dealer immediately.
Prepare the Remote Control
When you use the remote control for the first time, pull out
the insulation sheet.
To Replace the Battery in the Remote Control
NOTES:
• Store the battery in a place where children cannot reach. If
a child accidentally swallows the battery, consult a doctor
immediately.
• To prevent the battery from over-heating, cracking, or starting
a fire:
– Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing
away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal,
state, and local regulations.
• The batteries (battery pack or batteries installed) shall not be
exposed to excessive heat source such as sunshine, fire or the
like.
Basic Disc Operations
To Press Indication/Result
Play back the disc
• Current track number and elapsed playing
time appear.
For MP3/WMA files: Before current track
number and elapsed playing time appear, the
tag information appears if it is recorded.
• During playback, press again to pause.
Stop playback
• While playback is stopped, total track number
and total playing time (for MP3/WMA files,
group number and track number) appear.
Select a track
Select the next tracks.
To go back to the beginning of the current or
previous tracks.
Select a group
(MP3/WMA only)
Select the next groups while playback is
stopped.
Select the previous groups while playback is
stopped.
Forward search/
Reverse search
Press and hold to fast-forward the track during
playback.
To stop searching, release the button.
Press and hold to fast-reverse the track during
playback.
To stop searching, release the button.
NOTES:
• If no disc is inserted, “NO DISC” appears on the main display.
• If MP3/WMA files are not recorded on the disc, “NO PLAY” appears on the main
display.
Playing Repeatedly—Repeat Play
1
Press repeatedly to specify the repeat mode as follows:
REP TRK: Repeats the current (or specified) track. [ ]
REP GRP: Repeats all tracks in the current group (MP3/WMA
only). [ ]
REP ALL: Repeats all tracks. [ ALL ]
REP OFF: Normal playback
2
Getting Started
Playing Back a Disc
CAUTION:
• Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth,
etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted candles, on the apparatus.
• When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of
these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases,
shall be placed on the apparatus.
• Excessive sound pressure from earphones or headphones can cause hearing loss.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet. There
are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
Dear Customer,
This apparatus is in conformance with the valid European
directives and standards regarding electromagnetic
compatibility and electrical safety.
European representative of Victor Company of Japan,
Limited is:
JVC Technology Centre Europe GmbH
Company name changed in:
JVC Technical Services Europe GmbH
Postfach 10 05 52
61145 Friedberg
Germany
Precautions
Notes on the power cord
• When you are away on travel or otherwise for an extended period of time, remove the plug from the wall outlet.
• When unplugging the System from the wall outlet, always pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or moving the System.
• Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power cord replaced with a new one.
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and remove the plug from the wall outlet, then consult your dealer. Using
the System in this state may cause a fire or electrical shock.
• Do not expose the System to direct sunlight or place it near a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot nor too cold—between 5˚C and 35˚C.
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the System.
• Do not block the vents.
There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult your dealer.
MICRO COMPONENT SYSTEM
UX-GP5
—Consists of CA-UXGP5 and SP-UXG300
This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files
in ISO 9660 format.
• When playing back an MP3 or WMA track, MP3 or WMA indicator lights up.
Loading a Disc (on the System only)
1
Press to open the disc tray.
2
• When using an 8 cm disc, place it on the inner
circle of the disc tray.
3
Press to close the disc tray.
Prohibiting Disc Ejection (on the System only)
You can lock the disc tray so that no one can eject the loaded disc.
• This is possible while the System is on standby.
+
To cancel the prohibition, repeat the same procedure.
3
Programming the Playing Order—Program Play
1
During stops, press until the PRGM (program) indicator lights up
before playing.
2
or
• For MP3/WMA files: Select a group number, then a track
number.
• For CD: Select a track number.
3
Press to program the selected group/track.
4
Repeat steps 2 and 3 to program other tracks you want.
• If you try to program a 51st track, “FULL” will appear.
5
The tracks are played back in the programmed order.
Operations for Program Play (while not playing)
• To check the programmed contents, press 4 or ¢.
• To add tracks, repeat steps 2 and 3 above.
• To erase the last programmed track, press CANCEL.
• To erase the entire program, press and hold CANCEL for about 2 seconds.
• To exit from program play, press MODE.
– The stored program is kept.
Playing at Random—Random Play
1
Press until the RND (random) indicator lights up before you start
playback.
2
Playback starts in random order.
Random Play ends when all tracks are played back.
Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track, press 4.
• To exit from random play, press MODE while playback is stopped.
Thank you for purchasing a JVC product.
Lithium coin battery
(product number: CR2025)
Insulation sheet
Front view Side view
Information for Users on Disposal of Old
Equipment
[European Union only]
This symbol indicates that the product
with this symbol should not be disposed
as general household waste. If you want to
dispose of this equipment, please do not
use the ordinary dust bin! There is a separate
collection System for these products.
To
Press
Indication/Result
System Remote
Turn on or off
(standby) the power
The STANDBY lamp on the System turns off/on.
Select a source
See “Playing Back a Disc” on page 4 and “Listening to
an iPod” on page 5.
Press repeatedly to select “FM” or “AM.”
• For “FM/AM,” see “Listening to FM and AM
Broadcasts” on page 5.
See “Listening to Digital Audio Player” on page 6.
Adjust the volume
Adjustable range: Level 0 (“VOL MIN”) to level 40
(“VOL MAX”).
Drop the volume in a
moment
—
To restore the volume, press again, or adjust the
volume level.
Activate the EALA
surround mode —
The indicator lights up.
To cancel this function, press repeatedly until
indicator lights off.
Emphasize the
sound (Sound Turbo
function)
The S.TURBO indicator lights up.
To cancel this function, press again.
Reinforce the bass
sound (Active Hyper
Bass Pro function) —
Press and hold until the AHB indicator lights up.
• When Sound Turbo function is activated (see above),
this function cannot be activated.
To cancel this function, press and hold again when
Sound Turbo function is deactivated.
Adjust the tone
(Bass/Treble)
—
Press once for adjusting the bass level; twice for treble
level, then, press VOLUME +/–.
Adjustable range: –3 to +3.
Change the display
brightness
—
You can dim the display window and illumination
lamp.
While the System is turned on...
Change the display
information (Clock
and Source)
—
For setting the clock, see “Setting the Clock and Using
Timers” on page 6.
• Not applicable for FM.
Set the Save Mode
—
Press when the System is on standby.
Setting the save mode allows you to reduce power
consumption by turning the display off while on standby.
To cancel this function, press again when the System
is on standby.
NOTE:
DO NOT turn off (standby) the System with the volume set to an extremely high level;
otherwise, the sudden blast of sound can damage your hearing, speakers and/or
headphones when you turn on the System or start playback.
To a wall outlet
Plug the AC power cord only after all connections are complete.
Rear view
Outdoor FM antenna
(not supplied)
Disconnect the supplied FM antenna, and connect
to an outdoor FM antenna using a 75 Ω wire with
coaxial type connector (IEC or DIN45325).
FM antenna (supplied)
AM loop antenna (supplied)
Turn it until the best reception
is obtained.
RESUME Play
When you stop the playback by one of the following operations, this System
stores the beginning of the stopped track on the disc.
– Pressing 7 once
– Changing the source
When you start playback again, playback starts from the stored position.
To clear the stored position, open the disc tray.
• When you clear the stored position and start playback, playback starts from the
beginning of the first track.
NOTE:
This function does not work in Program Play and Random Play.
The following operations are explained using the remote control, unless
mentioned otherwise. However, if the System has the same or similar button
names, they can also be used for the operations.
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
NOTES:
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the antennas
away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception.
• Make sure both the speakers are connected correctly and firmly.
• When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.
Do not connect the AC power cord until all other connections have been made.
To connect the FM antenna (supplied)
Extend it so that you can obtain the best reception.
For better FM reception
To connect the AM loop antenna (supplied) To assemble the AM loop antenna
To connect the speaker cords
Using Headphones
Be sure to turn down the volume before connecting or putting on the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.
Press and hold
Insert
Release
Red
Black
From left
speaker
From right
speaker
Point at the remote sensor on the front panel.
(The operating range is approx. 7 m.)
STANDBY lamp
PHONES jack
Stereo mini plug cord
GVT0242-001A EN_UX-GP5[B]6
How to cancel the demonstration
Press and hold DEMO button while on standby. (Refer to the attached “Information
about the demonstration function.”)