Filter
Top Products
18
Turning off the power with the
sleep timer
Using the sleep timer, you can fall asleep while listening to
music.
From the remote control ONLY:
Press SLEEP.
Each time you press the button, the shut-off time changes as
follows:
0min (cancelled) ] 10min (minutes) ] 20min ]
30min ] 60min ] 90min ] 120min ] 150min ]
(back to the beginning)
Ex.: When “150min” is selected.
To check the remaining time until the shut-off time
Press SLEEP once.
The remaining time until the shut-off time appears on the
display for a while.
To change the remaining time until the shut-off time
Press SLEEP repeatedly to change the shut off time.
• Each time you press the button, the shut-off time changes.
To cancel the sleep timer
Press SLEEP repeatedly until “0min” appears on the display
window.
• Turning off the power also cancels the sleep timer.
NOTES:
• When DVD is selected as the source to play, this system can also
turn off automatically if playback is not restarted within the time you
have specified (Auto Standby). See page 56.
• If the shut-off time set by Auto Standby comes earlier than the one
set by the sleep timer, Auto Standby takes effect.
L
S.WFR
R
Changing the analog/digital
input mode and decoding mode
When playing software encoded with Dolby Digital or DTS
Digital Surround, the following symptoms may occur:
• Sound does not come out at the beginning of playback.
• Noise comes out while chapters or tracks are being
searched for or skipped over.
To fix these problems, set the correct decoding mode.
From the remote control ONLY:
Press DECODE to select the digital input
mode when DVD or DBS tuner is selected as
the source.
Each time you press the button, the input mode changes as
follow.
When DVD is selected as the source:
AUTO/PCM ] DOLBY D ] DTS ] (back to the beginning)
When DBS tuner is selected as the source:
ANALOG ] AUTO/PCM ] DOLBY D ] DTS ]
(back to the beginning)
• When you want to hear digital sound reproduced, connect
the center unit and the component through the optical digital
terminals.
ANALOG :Select when the DBS tuner is connected to
AUDIO IN jacks.
For Digital Connection
AUTO/PCM :Normally select this for the digital input mode.
The system automatically detects the
incoming signals.
DOLBY D :Select when playing software encoded with
Dolby Digital or Dolby Digital EX.
DTS :Select when playing software encoded with
DTS Digital Surround or DTS-ES.
The following are the digital signal indicators on the display to
indicate what type of signal comes into the system (see also
page 30).
LINEAR PCM :Lights when Linear PCM signal comes in.
DIGITAL EX :Lights when Dolby Digital EX signal
comes in.
DIGITAL :•Lights when Dolby Digital signal comes
in.
•Flashes when “DOLBY D” is selected for
software not encoded with Dolby Digital.
:•Lights when DTS or DTS-ES signal
comes in.
•Flashes when “DTS” is selected for
software not encoded with DTS.
NOTES for the digital input mode:
• If the incoming signal cannot be recognized when selecting
“AUTO/PCM,” no digital signal indicators light up on the display.
• Turning off the system or changing the source returns the input
mode to “AUTO/PCM” automatically.
Basic operations
AUDIO ANGLE SUBTITLE
DECODE
RETURN DIGEST
VFP
TOP MENU
MENU
CONTROL
EFFECT
S.WFR
TEST
SLEEP
TV
VCR
SETTING
TV RETURN
ENTER
ON
SCREEN
CHOICE
FM MODE
123
456
789
10
0
+10
100+
SOUND
SURROUND
OFF
DSP
CENTER
–
+
–
+
–
+
–
+
SURR-L
SURR-R
S-BACK
–
+
ADJUST
AUDIO/
TV/VCR
CATV/DBS
PROGRESSIVE
Set the remote
control mode
selector to
“AUDIO/TV/VCR.”
EN16-21.TH-A75[A]_f 02.10.11, 2:53 PM18