Filter
Top Products
14
Basic adjustment of auto memory
This receiver memorizes sound settings for each source:
• when you turn off the power,
• when you change the source, and
• when you change the analogue/digital input mode (see page 11).
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
The following can be stored for each source:
• Analogue/digital input mode (see page 11)
• Tone adjustment (see page 21)
• Balance (see page 21)
• Bass boost (see page 22)
• Input attenuator mode (see page 22)
• Subwoofer output level (see page 22)
• Subwoofer audio position (see page 22)
• Surround/DSP mode selection (see pages 28 – 33)
NOTE
If the source is FM or AM (MW), you can assign a different setting
for each band.
Signal and speaker indicators on the display
The following signal indicators light up —:
L: • When digital input is selected: Lights up when the left
channel signal comes in.
• When analogue input is selected: Always lights up.
R: • When digital input is selected: Lights up when the right
channel signal comes in.
• When analogue input is selected: Always lights up.
C: Lights up when the center channel signal comes in.
LS: Lights up when the left surround channel signal comes in.
RS: Lights up when the right surround channel signal comes in.
S: Lights up when the monaural surround channel signal
comes in.
LFE: Lights up when the LFE channel signal comes in.
The speaker indicators light up as follows:
• The subwoofer indicator (
SUBWFR
) lights up when “SUBWFR” is
set to “USE” for Quick Setup (see page 16) or to “YES” for
Manual Setup (see page 17).
• The other speaker indicators light up only when the
corresponding speaker is set to “SML” or “LRG,” and also when
required for the current playback.
Signal indicators Speaker indicators
Turning off the power with the Sleep
Timer
You can fall asleep while listening to music—Sleep Timer.
From the remote control ONLY:
Press SLEEP repeatedly.
The SLEEP indicator lights up on the display, and
the shut-off time changes in 10 minutes intervals.
ANALOG
PL ΙΙ
SUBWFR LFE
AUTO SR
INPUT ATT
DSP HP
LCR
LS S RS
LPCM
DOLBY D
DTS
SUBWFR
LCR
LS RS
LFE
LCR
LS S RS
ANALOG
SUBWFR
SLEEP
VOL
LR
10
20
30
40
50
60
70
90
80
0
(Canceled)
Basic operations
SLEEP indicator
When the shut-off time comes:
The receiver turns off automatically.
To check or change the remaining time until the shut-off time:
Press SLEEP once.
The remaining time (in minutes) until the shut-off time appears.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer:
Press SLEEP repeatedly until “SLEEP 0” appears on the display. (The
SLEEP indicator goes off.)
• Turning off the power also cancels the Sleep Timer.
Changing the display brightness
You can dim the display.
From the remote control ONLY:
Press DIMMER repeatedly.
• Each time you press the button, the indication
changes as follow:
DIMMER 1: • Dims the display slightly.
• Dims the blue indication
lighting source lamps.
DIMMER 2: • Dims the display more than
DIMMER 1.
• Dims the blue indication
lighting source lamps (same
as DIMMER 1).
DIMMER 3: Turns off the display and the
blue indication lighting source
lamps.
DIMMER OFF: Cancels the dim (normal
display).
NOTE
When setting speakers and basic items or adjusting sound, select
“DIMMER OFF” to confirm the setting you make on the display.
AUDIO
ZOOM
ANGLE
REPEAT
DIMMER
SUBWFR CENTER L RSURR
BASS BOOST
A.POSITION
SMART S. SETUP
SLEEP CANCEL
SURROUND
ANALOG/DIGITAL
TV RETURN 100
+
BASS TREBLE
SUBTITLE RETURN
TITLE/GROUP
BASS TREBLE
123
4
VFP
INPUT
TONE
TEST EFFECT
DECODE
56
789
10
3D
0 +10
AUDIO
ZOOM
ANGLE
REPEAT
DIMMER
SUBWFR CENTER L RSURR
BASS BOOST
A.POSITION
SMART S. SETUP
SLEEP CANCEL
SURROUND
ANALOG/DIGITAL
TV RETURN 100
+
BASS TREBLE
SUBTITLE RETURN
TITLE/GROUP
BASS TREBLE
123
4
VFP
INPUT
TONE
TEST EFFECT
DECODE
56
789
10
3D
0
11-14.RX-ES1&XV-N55[B]f 03.2.18, 1:47 PM14