Filter
Top Products
1
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing
to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical
instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
KD-R414/KD-R314
CD RECEIVER : INSTRUCTIONS/INSTALLATION
1009DTSMDTJEIN
EN
© 2009 Victor Company of Japan, Limited
GET0659-001A
[UI]
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your
complete understanding and to obtain the best possible performance from
the unit.
Basic operations
When you press or hold the following button(s)...
Main unit
Remote
controller
General operation
Turns on.
• When the power is on, pressing
/I/ATT on the remote controller also
mutes the sound or pauses. Press /I/ATT again to cancel muting or resume
playback.
Turns off if pressed and held.
Selects the available sources (if the power is turned on).
• If the source is ready, playback also starts.
Adjusts the volume level.
— Selects items.
—
• Mutes the sound while listening to a source. If the source is “CD“ or “USB (for
KD-R414),“ playback pauses. Press the control dial again to cancel muting or
resume playback.
• Confirms selection.
Selects the sound mode.
• Enters tone level adjustment directly (see page 2) if pressed and held
EQ BASS-TRE
on the main unit.
— Enters playback mode menu directly (see page 2).
— Returns to the previous menu.
—
Power off : Checks the current clock time.
Power on : Changes the display information.
Warning:
If you need to operate the unit while driving, be sure
to look around carefully or you may be involved in a
traffic accident.
Control dial Loading slot Display window
Auxiliary input jack
Ejects the disc
Detaches the panel
Remote sensor
• DO NOT expose to bright sunlight.
USB (Universal Serial Bus)
input jack
For KD-R414
[European Union only]
Preparations
How to attach/detach the control
panel
How to reset your unit
Reset the unit after installation is
completed.
• Your preset adjustments will
also be erased.
How to forcibly eject a disc
• You can forcibly eject the loaded disc even if the
disc is locked. To lock/unlock the disc, see page 2.
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit.
For safety...
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
Temperature inside the car...
If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.
Preparing the remote controller
(RM-RK50)
When you use the remote controller for the first time,
pull out the insulation sheet.
If the effectiveness of the remote controller
decreases, replace the battery.
Replacing the lithium coin battery
Caution:
• Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• Battery shall not be exposed to excessive heat such
as sunshine, fire, or the like.
Warning (about battery handling)
To prevent accidents and damage:
• Do not install any battery other than CR2025 or its
equivalent.
• Store out of reach of children.
• Do not recharge, short, or dismantle.
• Do not dispose of in fire.
• Do not carry around with other metallic materials.
• Wrap the battery with tape and insulate when
throwing away or saving it.
[Hold]
Insulation sheet
CR2025
1 Turn on the power.
2
3
Canceling the display demonstration
4 Select <DEMO OFF>.
5
6 Finish the procedure.
Setting the clock
1 Turn on the power.
2
3 Select <CLOCK>.
4 Select <CLOCK SET>.
5 Adjust the hour.
6 Adjust the minute.
7 Finish the procedure.
(Initial setting)
[Hold]
(Initial setting)
[Hold]
To play new discs
Remove any rough areas from the
inner and outer edges of the disc.
Do not use the following discs:
• Single CD (8 cm disc)
• Warped disc
• Disc with sticker and sticker residue
• Disc with stick-on label
• Unusual shape disc
• C-thru Disc (semi-transparent disc)
• Disc with transparent or semi-transparent parts on
its recording area
How to clean the connectors
Wipe the connectors with a cotton swab or cloth
moistened with alcohol.
Moisture condensation
Moisture may condense on the lens inside the unit.
Eject the disc and leave the unit turned on for a few
hours until the moisture has evaporated.
To keep discs clean
Wipe in a straight line from center
of disc to edge. Do not use liquid
cleaners, thinners, or benzene.
Maintenance
Connectors
Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries.
EN_KD-R414_R314[UI]3.indd 1EN_KD-R414_R314[UI]3.indd 1 10/27/09 5:10:16 PM10/27/09 5:10:16 PM