Filter
Top Products
25
Tuner operations
Tuner operations
Tuning in to stations manually
From the remote control ONLY:
1
Press FM/AM to select the band.
The last received station of the selected band is tuned in.
• Each time you press the button, the band alternates
between FM and AM.
2
Press repeatedly or hold TUNING 9 or
( TUNING until the station you want is tuned
in.
• Pressing (or holding) TUNING 9 increases the frequency.
• Pressing (or holding) ( TUNING decreases the frequency.
NOTES
• When you hold and release TUNING 9 or ( TUNING, the
frequency keeps changing until a station is tuned in.
• When a station of sufficient signal strength is tuned in, the
TUNED indicator lights up on the display.
• When an FM stereo program is received, the ST (stereo)
indicator also lights up.
Using preset tuning
Once a station is assigned a channel number, the station can be
quickly tuned simply by selecting the number. You can preset up to
30 FM and 15 AM stations.
To store the preset stations
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step
2
again.
From the remote control ONLY:
1
Tune in to the station you want to preset (see
“Tuning in to stations manually” above).
• If you want to store the FM reception mode for this station,
select the FM reception mode you want. See “Selecting the
FM reception mode” on page 26.
2
Press MEMORY.
The channel number position starts flashing on the display for
about 5 seconds.
CONTINUED ON THE NEXT PAGE
Tuner operations are mainly done from the remote control.
NOTE
When you have selected “FM” or “AM” by using SOURCE
SELECTOR on the front panel, the remote control may not
work for tuner operations. To use the remote control for tuner
operations, select “FM” or “AM” by using the source selecting
button on the remote control.
EQ
LPCM L
LS SB RS
S . WFR
PL
NEO : 6
DSP 3D
LFE
C R
DOLBY D
DTS AAC
96 / 24
AUTO SR
C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST SLEEP
AUTO MUTING AUTO MODE
ATT
HP
MHz
kHz
EQ
LPCM L
LS SB RS
S . WFR
PL
NEO : 6
DSP 3D
LFE
C R
DOLBY D
DTS AAC
96 / 24
AUTO SR
C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST SLEEP
AUTO MUTING AUTO MODE
ATT
HP
MHz
kHz
EQ
LPCM L
LS SB RS
S . WFR
PL
NEO : 6
DSP 3D
LFE
C R
DOLBY D
DTS AAC
96 / 24
AUTO SR
C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST SLEEP
AUTO MUTING AUTO MODE
ATT
HP
MHz
kHz
Setting the AM tuner interval spacing
(Except for Australia)
Some countries space AM stations 9 kHz apart, and other
countries use 10 kHz spacing. 9 kHz interval spacing is the initial
setting.
• Be sure the receiver is turned off, but is plugged into an AC
outlet when setting the AM tuner interval.
On the front panel ONLY:
To select the 10 kHz interval:
Hold down ADJUST and press STANDBY/ON.
“10k STEP” appears on the display.
To change back to the 9 kHz interval:
Hold down SETTING and press STANDBY/ON.
“9k STEP” appears on the display.
NOTE
When you change the AM tuner interval spacing, stored preset
stations are erased. In this case, restore stations.
When operating the
receiver using the remote
control, set the mode
selector to “AUDIO/TV/
VCR/DBS.”
25-26RX-F10S[USUXA]_1.p65 04.5.18, 2:32 PM25