Filter
Top Products
23
Switching to a Program of Your
Choice Automatically
Another convenient RDS service is called “Enhanced Other
Networks.”
This allows the receiver to switch temporarily to a broadcast
program of your choice (TA, NEWS, and/or INFO) from a different
source except in the following cases:
• When you are listening to non-RDS Networks—all AM (MW) and
some FM stations.
• When the last received FM station is a non-RDS Networks.
• When the receiver is in standby mode.
Before you start, remember...
• The Enhanced Other Networks function is only applicable to
preset FM stations.
• You can use the Enhanced Other Networks function while
listening to any source. However, to use the RDS operation
buttons on remote control, the remote control operation mode
must be for the tuner operations mode (see page 40).
From the remote control ONLY:
Press TA/NEWS/INFO repeatedly to select the program type(s)
you want.
• Each time you press the button, the program type(s) change, and
the corresponding indicators light up on the display.
TA: Traffic Announcement in your area.
NEWS: News.
INFO: Program the purpose of which is to impart advice in
the widest sense.
OFF: Cancels the Enhanced Other Networks function
TA
NEWS/INFO
NEWS
TA/NEWS/INFOOFF
INFO
TA/NEWS
TA/INFO
When the current source is “FM”
If the station currently tuned in starts
broadcasting the program you have selected
The receiver continues to receive the station, but the indicator
of received PTY code starts flashing.
When the program is over, the indicator of received PTY code
stops flashing and remains lit, but the receiver remains in
Enhanced Other Networks standby mode.
If another FM station starts broadcasting the
program you have selected while you are
listening to an FM station
The receiver automatically switches to the station. The
indicator of received PTY code starts flashing.
When the program is over, the receiver goes back to the station
previously tuned in, but still remains in Enhanced Other
Networks standby mode. The indicator of received PTY code
stops flashing and remains lit.
CASE 1
CASE 2
‘
‘
When the current source is other than “FM”
If a station starts broadcasting the program you
have selected while listening to current source is
other than “FM”
When a station is or starts broadcasting the program you have
selected, the receiver automatically switches to the station.
The indicator of received PTY code starts flashing.
When the program is over, the receiver goes back to the
previously selected source, but still remains in Enhanced Other
Networks standby mode. The indicator of received PTY code
stops flashing and remains lit.
CASE 3
‘
To stop listening to the program selected by the Enhanced Other
Networks function
Press TA/NEWS/INFO repeatedly so that the program type (TA/
NEWS/INFO) indicator goes off from the display. The unit enters
the Enhanced Other Networks function off mode and goes back to
the previously selected source.
Notes:
• Enhanced Other Networks data sent from some stations may not
be compatible with this receiver.
• In Enhanced Other Networks standby mode, if you carry out
synchronized recording (see page 39), Enhanced Other Networks
standby mode is canceled temporarily. The receiver goes back to
Enhanced Other Networks standby mode again when the recording
is finished.
• While listening to a program tuned in by the Enhanced Other
Networks function, you can only use the DISPLAY MODE button as
the tuner operation buttons.
CAUTION:
When the source alternates intermittently between the station tuned in
by the Enhanced Other Networks function and the currently selected
source, press TA/NEWS/INFO repeatedly to cancel the Enhanced
Other Networks function.
If you do not press the button, the currently tuned station is received
finally, and one of the TA/NEWS/INFO indicators flashing on the
display disappears.
If an “Alarm!” (or TEST) signal is received from a station,
the receiver automatically tunes in the station from any source
other than AM (MW).
• While receiving an emergency broadcast, “Alarm!” appears on
the display.
The TEST signal is used for testing the “Alarm!” signal.
Therefore, it makes the unit work in the same way as the
“Alarm!” signal does.
20-23_7032[B]f.pm6 03.3.6, 4:14 PM23