Filter
Top Products
10
TSS-1200 (120V)
OPERATION
Surround Modes
When using the system in a Dolby Digital or DTS home theater
system, make sure all speakers are set to “Small”. When using the
T
SS-1200 in a Dolby Pro Logic
®
h
ome theater system, make sure
the receiver’s center channel mode is set to “Normal.”
Some Dolby Digital-equipped receivers/processors offer different
setup options for each source or surround mode (e.g.,CD-stereo,
videotape, Dolby, Pro Logic). In each case, follow your equipment’s
instructions to ensure that the subwoofer output is turned on and
that the speakers are set to “Small”in each mode.
Power On
Plug your subwoofer’s AC cord into a wall outlet.Do not use the
outlets on the back of the receiver.
Initially set the Subwoofer-Level Control
ᕡ
to the“Min”position.
Turn on the subwoofer by pressing the Power Switch
ᕦ
on the
rear panel.
Turn on your entire audio system and start a CD or movie sound-
tr
ack at a moderate level.
Auto On/St
and-By
The subwoofer will automatically enter the Stand-By mode after
approximately 10 minutes when no signal is detected from your
system.The subwoofer will then power on instantly when a signal
is detected. During periods of normal use, the Power Switch
ᕦ
can be left on.You may turn off the Power Switch
ᕦ
for extended
periods of nonoperation, e.g., when you are away on vacation.
Adjust Level
Turn the Subwoofer-Level Control
ᕡ
up about halfway. If no
sound emanates from the subwoofer, check the AC-line cord and
input cables.Are the connectors on the cables making proper
contact? Is the
A
C plug connected to a
“li
v
e”receptacle? Has the
Power Switch
ᕦ
been pressed to the “On”position? Once you
have confirmed that the subwoofer is active, proceed by playing
a CD or D
VD. Use a selection that has ample bass information.
Set the overall volume control of the receiver/processor to a
comfortable level.Adjust the Subwoofer-Level Control
ᕡ
until
you obtain a pleasing blend of bass. Bass response should
not overpower the room but rather be adjusted so there is
a harmonious blend across the entire musical range. Many
users have a tendency to set the subwoofer volume too loud,
adhering to the belief that a subwoofer is there to produce lots
of bass.This is not entirely true.A subwoofer is there to enhance
bass, extending the response of the entire system so the bass
can be felt as well as heard. However, overall balance must
be maintained or the music will not sound natural.An experienced
listener will set the volume of the subwoofer so its impact on
bass response is always there but never obtrusive.
Crossover Adjustment
T
he Crossover-Frequency Control
ᕤ d
etermines the highest
frequency at which the subwoofer reproduces sounds. For the
TSS-1200, it is recommended that this control be set at 120Hz
(approximately the 3 o’clock position).
N
OTE:
T
his control will have no effect if the LFE/Normal Switch
ᕢ is set to “LFE.”If you have a Dolby Digital or DTS receiver/
processor, the low-pass frequency is set by the receiver/
p
rocessor. Set the LFE/Normal Switch
ᕢ o
n the subwoofer to
“LFE.”Consult your owner’s manual to learn how to view or
change this setting.A setting of 120Hz – 150Hz is recommended.
Phase Control
The Phase Switch ᕣ determines whether the subwoofer
speaker’s piston-like action moves in and out with the main
speakers, 0˚, or opposite the main speakers, 180˚. Proper phase
adjustment depends on several variables such as room size,
subwoofer placement and listener position.Adjust the Phase
Switch
ᕣ to maximize bass output at the listening position.
Final Positioning
After correctly connecting the TSS-1200 system and verifying
that both the subwoofer and all satellite speakers are playing, it
is time to optimize the system for your particular listening room.
Earlier, you placed the subwoofer in its general location. Finding
the exact location for optimum performance sometimes only
involves moving the speakers up to a few inches in any direction.
We urge you, therefore, to experiment with placement, if possible,
until your speakers deliver their full potential.
MAINTENANCE AND SERVICE
The satellite and subwoofer enclosures may be cleaned using a
soft cloth to remove fingerprints or to wipe off dust.
All wir
ing connections should be inspected and c
leaned or
remade periodically.The frequency of maintenance depends on
the metals inv
olved in the connections
,
atmospheric conditions
and other factor
s
,
but once per year is the minimum.
If a problem occurs,make sure that all connections are properly
made and clean. If a problem exists in one loudspeaker, reverse
the connection wir
es to the left and r
ight system. If the pr
oblem
r
emains in the same speaker, then the fault is with the loud-
speaker. If the problem appears in the opposite speaker, the
cause is in another component or cable. In the event that your
TSS-1200 e
v
er needs ser
v
ice
, contact your local Infinity dealer
or distr
ibutor or www.inf
initysystems.com for a service center
near you.
TSS-1200 OM-no LED 9/27/06 2:03 PM Page 12