Filter
Top Products
PROGRAMMED PLAY OPERATION 13
Programmed Play Operation
ENGLISH
The HD 990’s advanced programming capability
enables you to select certain tracks, to preset the
order in which these tracks play, and to clear
specific programmed tracks after the program
was made.
Programmed Play
Programmed play allows you to program up to
32 tracks into the HD 990’s memory. To begin
programming the CD player, make sure that the
unit is in Stop mode, then press the Program
button
3
. The PROGRAM indicator will light
in the Information Display
1
, the number
001 will blink below the Program indicator,
showing the track number selected, and
PROG-01: 001 will appear in the
Information Display, replacing the track time.
This indicates that you are about to program the
first track.
You may now begin to enter the tracks in the
order in which you wish to have them play. To
select a track on the disc, press the Numeric
buttons
2
corresponding to the desired track,
be certain to enter the second and/or third num-
ber of two- or three-digit numbers within two
seconds after the first number was entered. You
may also use the Skip buttons
78
7
to
select a track. When the track is selected, press
the Program button
3
. Note that the
program-step indication on the right side of
the Information Display will change to
PROG-02: 001.
You may now select another track for the next
program step, following the instruction shown
above. When the track is selected, press the
Program button
3
again. Repeat this proce-
dure for each program step until you have com-
pleted the desired programming. Press the Stop
button
6
A
once to complete a program
sequence, or press Play
4
9
to begin
immediate play of a program sequence. If the
maximum of 99 program steps is reached, the
program-step indication at the right side of the
Information Display will go out, and the disc and
track that have been programmed as the first
program step will be shown.
Once a program list has been entered, press the
Play button
4
9
to begin listening to the
sequence. After the entire program has been
played, the CD player will stop. As long as the
Stop button
6
A
has not been pressed twice
and the PROGRAM indicator remains lit, you
may repeat the programmed-play sequence
again by pressing the Play button
4
9
.
Editing a Program
A program can be edited even after it was com-
pleted by pressing the Stop button
6
A
once: Each time you press the Program button
3
the track number and program step number
will be displayed in the programmed order, but
with steady tracks numbers (not blinking) in con-
trast to the programming mode. As soon as the
track number starts blinking (this will take
1 second), the appropriate program step number
shown at the left side is not programmed yet;
now you can change the track number with the
Skip buttons
78
7
or the Numeric but-
tons
2
as described above and add it to the
program list by pressing the Program button
3
.
Pressing the Stop button
6
A
twice will
return to normal mode and the PROGRAM indi-
cator will go out, but the program will stay in
memory and can be recalled easily by pressing
the Program button. But pressing the Clear
button
4
(see below) or opening the disc
drawer by pressing Open/Close
3
F
, will
erase the program information from the unit’s
memory.
Checking Program Contents
To check the contents of a program while the
unit is stopped at first note that the PROGRAM
indicator is lit (otherwise press Program) and
the program step indication PROG-01: is
not lit (otherwise press Stop once). Each time
the Check button
E
is pressed now, the
Information Display will step through each of the
pro grammed tracks. To cancel the check mode
press the Stop button twice.
Clearing Programs
To clear a single track from the program list, press
the Program button
3
until the track to be delet-
ed from the program sequence appears in the
Information Display
1
. When the track number
appears, press the Clear
4
once, the track
selected will be deleted and the track number
will be replaced by the next programmed one.
Now you can delete that track too with the
Clear button or press the Stop button
6
A
and again the Program
3
button to select
lower track numbers to be deleted.
When the unit is stopped and the program step
indication PROG-01: 001 is not lit (other -
wise press Stop once), but the PROGRAM indica-
tor is still lit (otherwise press Program
3
) you
may clear the entire contents of a program by press-
ing the Clear button
4
.
Important Note: When you’ve pressed the
Program button
3
(once or several times) and
the track number on the right starts blinking, the
appropriate program step number (e.g.
PROG-02: 008) shown at the left display
side is not programmed yet. Do not continue to
press the Program button now, otherwise the
track selected will be memorized too. If you´re in
doubt, press Stop button
6
A
and start the
procedure again with Program
3
.
IMPORTANT NOTE: Tracks programmed as
described above in chapter ”Programmed Play”
can be played repeatedly too: When you press
Repeat
5
once after a program is created
(the PROGRAM indicator must be lit, (otherwise
press Program) and the program is played, the
REPEAT 1 indicator will light and the track
currently playing will be repeated continuously.
If Repeat is pressed twice REPEAT ALL will be
displayed, all programmed tracks will be played
subsequently and the sequence will be repeated
continuously until the Stop button is pressed.
0046CSK - HD990 ENG_v5.qxp:0046CSK - HD990 ENG_v0.qxp 19/09/08 10:19 Side 13