Filter
Top Products
PROGRAMMING THE REMOTE 45
ENGLISH
Programming the Remote
To program the remote for Volume Punch-
Through, follow these steps:
1. Press and hold the Input Selector
4
for the
unit you wish to have associated with the volume
control until the red light illuminates under the
Input Selector
4
and note that the Program
Indicator
2
will flash amber.
2. Press the Volume Up button
d
and note
that the Program Indicator
2
will stop
flashing and stay amber.
3. Press either the AVR Selector
5
or the
Input Selector
4
, depending on which
system’s volume control you wish to have attached
for the punch-through mode. The Program
Indicator
2
will blink green three times and
then go out to confirm the data entry.
Example: To have the AVR’s volume control
activated even though the remote is set to
control the TV, first press and hold the VID1
Input Selector
4
Next, press the Volume Up
button
d
, followed by the AVR Input Selector
5
.
NOTE: Should you wish to return the remote to
the original configuration after entering a Volume
Punch-Through, you will need to repeat the steps
shown above. However, press the same Input
Selector in steps one and three.
Channel Control Punch-Through
The AVR’s remote may be programmed to operate
so that the channel control function, performed
with the Sleep/Program Up
9
and
Surround/Program Down
A
buttons, for
either the TV, cable or satellite receiver used in
your system may be used in conjunction with one
of the other devices controlled by the remote. For
example, while using and controlling the VCR,
you may wish to change channels on a cable box
or satellite receiver without having to change the
device selected by the AVR or the remote. To
program the remote for Channel Control Punch-
Through, follow these steps:
1. Press and hold the Input Selector button
4
for the device you wish to have the channel con-
trol associated with until the red light illuminates
under the Input Selector
4
and the Program
Indicator
2
flashes amber.
2. Press the Volume Down button
d
. The
Program Indicator
2
will stop flashing and
stay amber.
3. Press and release the AVR
5
or Input
Selector button
4
for the device that will be
used to change the channels. The Program
Indicator
2
will blink green three times and
then go out to confirm the data entry.
Example: To control the channels using your TV
while the remote is set to control the AVR, first
press and hold the VID 1 Input Selector button
4
. Next, press the Volume Down button
d
,
followed by the AVR Selector (bold) button..
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original
configuration, repeat the steps shown in the
example above. However, press the same Input
Selector in Steps 1 and 3.
Transport Control Punch-Through
The AVR’s remote may be programmed to operate
so that the Transport Control Functions
P
(Play, Stop, Fast Forward, Rewind, Pause and
Record) for a VCR, DVD or CD will operate in
conjunction with one of the other devices con-
trolled by the remote. For example, while using
and controlling the TV, you may wish to start or
stop your VCR or DVD without having to change
the device selected by the AVR or the remote. To
program the remote for Transport Control Punch-
Through, follow these steps:
1. Press and hold the Input Selector
4
for
the device you wish to have the channel control
associated until the red light illuminates, under
the Input Selector
4
and the Program
Indicator
2
flashes amber.
2. Press the Play button
P
. The Program
Indicator
2
will stop flashing and stay amber.
3. Press and release the AVR
5
or Input
Selector button
4
for the device that will be
used to change the channels. The Program
Indicator
2
will blink green three times and
then go out to confirm the data entry.
Example: To control the transport of a CD player
while the remote is set to control the TV, first press
and hold the Vid2 Input Selector button
4
until the Program Indicator flashes amber. Next
press the Play button
P
, followed by the CD
Input Selector button
4
.
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original
configuration, repeat the steps shown in the
example above. However, press the same Input
Selector in Steps 1 and 3.
NOTE: Before programming the remote for
Volume, Channel or Transport Punch-Through,
make certain that any programming needed for
the specific TV, CD, DVD, Cable or Satellite
Receivers has been completed.
Resetting the Remote Memory
As you add components to your home-theater
system, occasionally you may wish to totally
reprogram the remote control without the
confusion of any commands, macros or ”Punch-
Through“ programming that you may have done.
To do this, it is possible to reset the remote to the
original factory defaults and command codes by
following these steps. Note, however, that once
the remote is reset, all commands or codes that
you have entered will be erased and will need to
be re-entered:
1. Press any of the Input Selector buttons
4
and the ”O“ button
H
at the same time until
the Program Indicator
2
begins to flash
amber.
2. Press the ”3“ button
H
three times.
3. The red LED under the Input Selector
4
will go out and the Program Indicator
2
will
stop flashing and turn green.
4. The Program Indicator
2
will remain
green until the remote is reset. Note that this
may take a while, depending on how many
commands are in the memory and need to be
erased.
5. When the Program Indicator
2
goes out,
the remote has been reset to the factory settings.