Filter
Top Products
Page 6
TARGET LIGHT:
1. Push the TARGET LIGHT SWITCH (20) firmly and the
TARGET LIGHT (21) will raise into position and illuminate the
stylus tip.
2. To lower the TARGET LIGHT, push down on it until it locks in
the casing.
3. When not being used, the TARGET LIGHT should be kept in
the lowered position.
XLR LAMP ADAPTOR:
1. Plug a gooseneck light with an XLR base, like the GEMINI GNL-
500, into the XLR LAMP ADAPTOR (22).
2. When the power is turned on, the light will illuminate.
ADJUSTING THE PITCH CONTROL:
1. The PT-2000 is equipped with PITCH CONTROL (23) and
QUARTZ LOCK (25). When the QUARTZ LOCK is activated,
the PITCH LED (24) lights GREEN, and the speed will be
exactly 33 1/3 or 45 RPM depending on which SPEED
SELECTOR BUTTON (17) is pushed. PITCH CONTROL
automatically disengages when QUARTZ LOCK is activated.
2. When the QUARTZ LOCK is off, you can adjust the PITCH
CONTROL(23). When you move PITCH CONTROL (23) off
center, the pitch can vary +/- 10% depending on the position of
the PITCH CONTROL.
3. Push the QUARTZ LOCK (25) button to bring the speed back
to exactly 33 1/3 or 45 RPM when the PITCH CONTROL (23)
is positioned off center. Disengaging the QUARTZ LOCK (25)
will bring the platter speed back to the original pitch setting.
4. The PLATTER (2) is equipped with a STROBE RPM
INDICATOR STRIP (26) and the POWER SWITCH (15)
contains built in STROBE LIGHTS (27). When the PLATTER
(2) is spinning, the STROBE LIGHTS illuminate the STROBE
RPM INDICATOR STRIP (26). The bottom row of dots will
appear to be stationary when the speed of the platter is
exactly 45 RPM. The second row from the bottom will appear
to be stationary at 33 1/3 RPM.
ARM-LIFT HEIGHT ADJUSTMENT:
If the pre-adjusted distance that the CUE LEVER (18) raises the
stylus off the record surface is inadequate, it can be adjusted by
turning the ARM-LIFT HEIGHT ADJUSTMENT SCREW (28) while
simultaneously pushing down on the TONE ARM (5). Clockwise
rotation of the screw will decrease the distance and
counterclockwise rotation will increase the distance.
Specifications
TURNTABLE SECTION:
Type......................................Quartz Direct Drive Manual Turntable
Drive Method.................................................................Direct Drive
Motor........................................................Brushless DC Motor 18V
Platter...............................Aluminum Diecast 11 ½” (332mm) Dia.
Weight.................2 lbs. (0.9 Kg)
Speed..................................................................33 1/3 or 45 RPM
Starting Torque................................................1.5 Kg/cm (1.3 lb/in)
Build-up Characteristics................0.6 sec. standstill to 33 1/3 RPM
Braking System......................................................Electronic Brake
Wow and Flutter.......................................................0.01% WRMS*
* This rating refers to the turntable assembly and platter only and
excludes effects of records, cartridges or tonearms.
Rumble..............................................................78 dB (IEC 98A WTD)
TONEARM SECTION:
Type.............................................Universal S-Shaped Tubular Arm
Effective Length.................................................9 1/16” (230.1 mm)
Arm Height Adjust Range..................................................0 - 6 mm
Overhang..............................................................19/32" (15.2 mm)
Effective Mass..............................................9 g (Without Cartridge)
Offset Angle...............................................................................22°
Friction........................................Less Than 7 mg (Lateral, Vertical)
Tracking Error Angle.....Within 2°32' at the outer groove and within
0°32' at the inner groove of a 30 cm (12") record
Stylus Pressure Adjust Range............................................0 - 2.5 g
Applicable Cartridge Weight Range.....................................6 - 10 g
Headshell Weight.....................................................................5.6 g
GENERAL:
Power Supply.................................................................115V 60Hz
or
Power Supply.................................................................230V 50Hz
Power Consumption...........................................................15 Watts
Dimensions..........................................................17 ½” x 6 1/4" x 14"
444.5mm x 158.75mm x 355.6mm
Weight..................................................................25 lbs. (11.34 Kg)
Specifications are subject to change without notice. The weight and
dimensions shown are approximate.