Filter
Top Products
(3)
VOLTAGE SELECTOR: To set the proper voltage, adjust the VOLTAGE SELECTOR (1) switch to 115 or 230 volts.
POWER JACK (AC IN): Connect the power plug into the POWER JACK (2) for power.
REMOTE CONTROL: Use the included CABLE & REMOTE CONTROL (3) jacks to connect the REMOTE CONTROL to the MAIN UNIT.
LINE OUTPUT JACKS: LINE OUTPUT JACKS (4) provide stereo sound via included RCA cables to your mixer or receiver.
NOTE: MAKE SURE CABLES ARE PLUGGED IN TIGHT FOR OPTIMAL SOUND.
DIGITAL OUTPUT (COAXIAL): Use the COAXIAL (5) jack to connect to any type of device that accepts digital signals.
POWER: Press the POWER (6) button to turn on the CD player.
NOTE: MAKE SURE VOLTAGE SELECTOR SWITCH (1) IS SET BEFORE USE.
DISC TRAY: Put a CD in the DISC TRAY (7) after pressing STOP (8); trays hold both 12 cm and 8 cm CDs.
STOP: Tap the STOP (8) button once to STOP the CD, twice to open the DISC TRAY (7), and a third time to close the tray.
NOTE: THE STOP (8) BUTTON ONLY FUNCTIONS AS STOP AND EJECT ON THE REMOTE CONTROL.
DISPLAY: The DISPLAY (9) shows the various functions for the CD Player. See FUNCTION DESCRIPTIONS for details.
PLAYBACK DISPLAY BAR: The PLAYBACK DISPLAY BAR (10) shows the TIME ELAPSED and TIME REMAINING.
PLAY/PAUSE: Press PLAY/PAUSE (11) button to activate PLAY or PAUSE mode. See CUE or ROBO START INSTRUCTIONS for details.
CUE/PREVIEW: Tap CUE/PREVIEW (12) to come back to a set CUE or press and hold to PREVIEW from a CUE POINT, refer to CUE INSTRUCTIONS.
TRACK: Press the TRACK (13) buttons to select which TRACK to play.
SEARCH: Use the SEARCH (14) buttons to scan forward and reverse directions on a TRACK.
TIME: Tap the TIME (15) button to switch the TIME preference in three modes: ELAPSED, REMAIN, TOTAL REMAIN.
SINGLE: Tap SINGLE (16) for SINGLE AUTO CUE, CONTINUOUS, and NORMAL modes.
FLY CUE: FLY CUE (17) sets a SEAMLESS LOOP CUE POINT on the fly.
CUE-B/EXIT: Press CUE-B/EXIT (18) in PLAY mode, after a CUE POINT is memorized to start a LOOP, press again to exit LOOP.
RELOOP STUTTER: To play from a saved CUE POINT or a LOOP, press RELOOP STUTTER (19) to play the LOOP or the CUE again
.
MEMO (CUE 1-3): Press MEMO (20), then select a CUE POINT from CUE1-3 (20) followed by the same number again to set a CUE POINT.
Press CUE1-3 (20) to play from the set CUE POINT.
JOG WHEEL: The JOG WHEEL (21) has various functions such as PITCH BEND, CUEING, VINYL MODE, and EFFECT PARAMETERS.
JOG MODE: Press to change the JOG MODE (22) of the JOG WHEEL (21) from CD to VINYL mode.
EFFECT: Press an EFFECT button: FILTER, ZOOM, TRANS, or ECHO (23), to activate an EFFECT. Tap the EFFECTS (23) button to release.
MASTER TEMPO: Pressing MASTER TEMPO (24) locks the PITCH of a track with no change in vocal or instrument tone.
PITCH BEND: Buttons for PITCH BEND (25), lower or raise the pitch percentage (- or + 4%) when pressed.
PITCH: The PITCH (26) button activates the PITCH CONTROL SLIDE (27).
PITCH SELECT (4%, 12%, 24%, & 100%): Use the PITCH SELECT (27) button to change the PITCH settings from 4%, 12%, & 24%.
Press and hold for 100% PITCH.
PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE (28) up or down will lower or raise the pitch percentage.
ROBO START: Using ROBO START (29) enables you to alternate play between two CDs using both sides.
PGM (PROGRAM): First choose a side by selecting A or B (30). For track programming press PGM (30) then enter a track number followed by
PGM (30) and so-forth. For direct selection press a TRACK NUMBER followed by SET (30) then PLAY/PAUSE (11) to jump to that track.
NOTE: FOR FURTHER EXPLANATION PLEASE SEE PGM SECTION.
QUICK STQUICK ST
QUICK STQUICK ST
QUICK ST
ARAR
ARAR
AR
T GUIDET GUIDE
T GUIDET GUIDE
T GUIDE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30