Filter
Top Products
Page 3
IMPORTANT NOTE
Since the CD-2000X is a dual CD player, most of the functions and
controls are duplicated on both sides of the CD player. To eliminate
confusion and to make the drawings easier to understand, we will only
number the right side functions and controls. The only controls that are
not duplicated are the ROBO START (1), POWER BUTTON (21) and the
VOLTAGE SELECTOR SWITCH (30).
LINE VOLTAGE SELECTION
Model CD-2000X is a dual voltage unit. It will operate at 115 or 230 volts.
To set the proper voltage follow these steps:
1. Place the head of a screw driver in the center of the VOLTAGE
SELECTOR SWITCH (30) found on the rear panel.
2. Slide the switch left for 115 volts or push the switch right for 230 volts.
3. Do not force or twist the switch. Excessive force may cause damage. If
the switch does not move smoothly, contact a qualified technician.
CONNECTIONS
1. Using the included cables, plug one end into the REMOTE CONTROL
connector (31) on side 2 and the other end into the MAIN UNIT
connector (32) also on side 2. Do the same for side 1.
**IMPORTANT NOTE: YOU MUST CONNECT SIDE 1 ON THE REMOTE
CONTROL TO SIDE 1 ON THE MAIN UNIT AND SIDE 2 ON THE
REMOTE CONTROL TO SIDE 2 ON THE MAIN UNIT. IF YOU CROSS
THEM (for example the Remote Control on Side 1 to the Main Unit
on Side 2) THE CD-2000X WILL NOT WORK.
2. Plug one end of a set of RCA connectors into each of the LINE OUTPUT
JACKS (33).
3. Plug the other end of the RCA connectors into any available line level
input jacks on your mixer. If you are playing the CD-2000X through a
receiver, you can plug the RCA connectors into the CD or AUX INPUT
JACKS on your receiver. If there are no CD or AUX INPUTS, use any
line level (not phono) inputs.
FUNCTION DESCRIPTIONS
ANTI-SHOCK BUFFER MEMORY: With 12 SECONDS OF ANTI-SHOCK
BUFFER MEMORY, each side of the CD player stores 6 seconds of
future play to ensure that any harsh movement or bumping of the unit
will not interrupt play and play will continue smoothly.
POWER: After making sure that the VOLTAGE SELECTOR switch (30),
found on the rear panel, is properly set, plug the unit in and press the
POWER button (21). The unit will turn on. Pushing the POWER button
(21) a second time will turn the unit off.
DISC TRAY: The DISC TRAY (20) is where the CD is held during loading,
unloading and playback. Pressing the disc tray OPEN/CLOSE BUTTON
(27), will open or close the tray. The DISC TRAY (20) holds both 12 cm
and 8 cm CDs. Please note, if the CD-2000X is in the play mode, the tray
will not open.
OPEN/CLOSE BUTTON: Press the OPEN/CLOSE BUTTON (27) to load
or remove a CD from the DISC TRAY (20).
DISPLAY: The DISPLAY (5) shows the track number, pitch value, single-
auto cue, continue (for continuous play), and 3 different time displays.
These time displays are time elapsed on the track, time remaining on the
disc and time remaining on the track. Time is measured in minutes,
seconds and frames. It also shows the beats-per-minute of the track.
THE BPM/PITCH BUTTON (37) allows you to select what you would
like displayed, either the PITCH PERCENTAGE or the BPM.
PLAYBACK DISPLAY: The PLAYBACK DISPLAY (6) displays the time
remaining to play and flashes slowly when the track has 30 seconds
left. The PLAYBACK DISPLAY (6) flashes quickly when the track has
15 seconds left.
PLAY/PAUSE : Each press of the PLAY/PAUSE BUTTON (17) causes
the operation to change from play to pause or from pause back to play.
TRACK SKIP : The TRACK SKIP BUTTONS (13) let you select the
track to play.
SEARCH BUTTONS : The SEARCH BUTTONS (28) are used to
move forward or reverse while in play or pause mode. See the CUE
INSTRUCTIONS section for more information.
JOG WHEEL: The JOG WHEEL (9) has various functions. Use the JOG
WHEEL (9) to make fine adjustments in pause mode. Use the JOG
WHEEL (9) to bend the pitch for precise synchronization in play mode,
for scratching, and adjustments to cue and effects parameters.
STOP : The STOP BUTTON (4) will end the playing of the CD as well as
clear sampler.
TIME: The TIME BUTTON (2) switches the time display between the three
available choices listed under DISPLAY.
FLY CUE: The FLY CUE (10A) function lets you set cues on the fly with
one press of a button. With the unit in the play mode (play/pause LED
glows green), press FLY CUE (10A) at the point where you want the
cue point to be (the unit will continue to play). The cue point is now
memorized. Press the CUE BUTTON (16) to return to the memorized cue
point. Push the PLAY/PAUSE BUTTON (17), and the unit will instantly
play from the spot selected.
CUE: With the unit in the play mode (play/pause LED glows green), and
after the cue point has been memorized, pressing the CUE BUTTON
(16) will cause the CD player to enter the pause mode (play/pause LED
blinks green) at the memorized cue point (the cue LED glows red).
Holding down the CUE BUTTON changes the cue function to PREVIEW
(allowing you to hear the music play at whatever tempo you adjusted to
by holding the cue button down). Releasing the CUE BUTTON returns
you to the preset cue point.
SEAMLESS LOOP: After a cue point is memorized, pressing the CUE B/
EXIT BUTTON (11) in play mode, repeats the section between the cue
point and the point where the CUE B/EXIT BUTTON (11) was pressed.
Press the CUE B/EXIT BUTTON (11) again or pause play to exit the
repeating play.
SINGLE-AUTO CUE/CONTINUOUS: Pressing the SINGLE-AUTO CUE/
CONTINUOUS BUTTON (3) activates the AUTO CUE FUNCTION. The
AUTO CUE FUNCTION causes the unit to pause at the beginning of
music of the following track and allows you to start play immediately
from the start of music without any blank space (which exists at the
INTRODUCTION
Congratulations on purchasing a Gemini CD-2000X Dual CD Player.
This state of the art professional CD player is backed by a three year
warranty, excluding lasers. One year warranty on CD lasers. Prior to
use, we suggest that you carefully read all the instructions.
CAUTIONS
Do not use this CD Player at temperatures below 41°F/5°C or higher
than 95°F/35°C.
The apparatus should not be exposed to dripping or splashing and no
objects filled with liquids such as vases should be placed on the
apparatus.
Place the unit in a clean and dry location.
Do not place the unit in an unstable location.
When disconnecting the power cord from an AC outlet, always grasp it
by the plug. Never pull the power cord.
To prevent electric shock, do not remove the cover or the bottom
screws. There are no user serviceable parts inside. Please refer
servicing to a qualified technician.
Do not use chemical solvents to clean the unit.
Keep the laser pickup clean by keeping the drawer closed.
Keep this manual in a safe place for future reference.
SAFETY CERTIFICATIONS
Laser Diode Properties
Material: Ga - Al - As
Wavelength: 755 - 815 nm (25° C)
Laser Output: Continuous Wave, max. 0.5mW