Filter
Top Products
WEIGHT (8) will cause the cartridge side of the TONE
ARM (7) to be lowered; turning it clockwise will cause the
opposite. Turn the COUNTERWEIGHT (8) clockwise or
counter clockwise as needed until the TONE ARM (7) is
balanced horizontally. You can easily tell this by watching
for the point where the TONE ARM (7) “floats” freely.
4. Place TONE ARM (7) on ARM REST (11) and lock it in
place with the ARM CLAMP (10).
5. With the TONE ARM (7) locked on the ARM REST (11),
hold the COUNTERWEIGHT (8) steady with one hand
while rotating the STYLUS PRESSURE RING (9) until the
numeral “0” on the ring aligns with the center line on the
TONE ARM (7) rear shaft. The horizontal zero (0) balance
should be completed.
6. Re-float the TONE ARM (7) to ensure horizontal zero
(0) balance. If zero balance has not been maintained,
repeat counterweight steps 3 - 5.
7. After adjusting the horizontal zero (0) balance, turn the
balanced COUNTERWEIGHT (8) counter clockwise until
the cartridge manufacturer’s recommend stylus pressure
appears on the STYLUS PRESSURE RING (9) where it
meets the center line of the TONE ARM (7) rear shaft.
ADJUSTING THE ANTI-SKATING CONTROL:
Set the ANTI-SKATING CONTROL (12) to the same
value as the stylus pressure.
NOTE: IF YOUR TURNTABLE CAME WITH A CN-1000 CARTRIDGE,
IT HAS A RECOMMENDED TRACKING FORCE OF 3.0 GRAMS AND
CAN HAVE RANGE FROM 2.5-3.5 GRAMS.
CONNECTIONS:
1. Plug the AC power plug into an appropriate outlet.
2. See Table A for proper connection of the output RCA
plugs and ground connector. Make sure that all the plugs
are firmly plugged into the appropriate jacks (phono
inputs).
NOTE: TO REDUCE HUM, MAKE SURE THE GROUND LUG IS FIRM-
LY CONNECTED TO THE GROUND SCREW.
TABLE A:
OPERATING INSTRUCTIONS:
BASIC OPERATION:
1. Place a record on the SLIPMAT (4) which sits on the
PLATTER (2).
2. Select the desired speed by depressing the 33 or 45
SPEED SELECTOR (16) button.
3. Turn the POWER (13) switch to the “ON” position, at
which point the TARGET LIGHT (14) will light up, TAR-
GET LIGHTS (14) are an optional accessory available at
your local retailer.
4. Remove the stylus protector (if applicable to your car-
tridge).
5. Release the ARM CLAMP (10) found on the ARM
REST (11).
6. Push the START/STOP (15) button. The turntable
PLATTER (2) will start to spin.
7. Carefully position the TONE ARM (7) over the desired
position over the record. Lower the TONE ARM (7) slow-
ly, while letting go of the TONE ARM (7) over the record
where you want to play.
8. When play is over, raise the TONE ARM (7), move it
onto the ARM REST (11), and secure it with the ARM
CLAMP (10).
9. You now have the option of turning off the power by
turning the POWER (13) switch to the “OFF” position, or
stopping the PLATTER (2) by pushing the START/STOP
(15) button.
INTERRUPTING PLAY:
1. Pushing the START/STOP (15) button will cause the
record to stop exactly when the START/STOP (15) button
is pressed while playing.
2. Press the START/STOP (15) button again to start play-
back with a short DELAY effect.
ADJUSTING THE PITCH CONTROL:
1. The TT-02 MKII is equipped with a PITCH CONTROL
(17). When the PITCH CONTROL is in the center posi-
tion, the speed will be 33 or 45 depending on which
SPEED SELECTOR (16) button is pushed.
2. When the PITCH CONTROL (17) is positioned off cen-
ter, the pitch can vary ±10% depending on the position of
the PITCH CONTROL (17).
SPECIFICATIONS:
TURNTABLE SECTION:
Type.......................................Direct Drive Manual Turntable
Drive Method.......................................................Direct Drive
Motor......................................................................DC Motor
Speed........................................................33 1/3 or 45 RPM
Wow and Flutter............................Less than 0.25% WRMS*
*THIS RATING REFERS TO THE TURNTABLE ASSEMBLY AND
PLATTER ONLY AND EXCLUDES EFFECTS OF RECORDS, CAR-
TRIDGES OR TONEARMS.
TONEARM SECTION:
Type.............................Statically Balanced Straight Tonearm
Headshell Weight...........................................................5.6 g
GENERAL:
Power Supply.........................AC 115 V~60 Hz/230 V~50 Hz
Power Consumption......................................................15 W
Dimensions.............................................17.75" x 5.75” x 14"
............................................................(450 x 136 x 352 mm)
Weight.........................................................12.5 lbs. (5.7 kg)
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
THE WEIGHT AND DIMENSIONS SHOWN ARE APPROXIMATE.
(5)
OUTPUT CONNECTORS MIXER OR RECIEVER
L (WHITE) PHONO L CHANNEL
R (RED) PHONO R CHANNEL
GND (SPADE LUG) GND SCREW