FUNAI NB530SLX CD Player User Manual


 
47EN
OTHERS
Servicing
Please refer to relevant topics on “Troubleshooting” on
page 44 before returning the product.
If this unit becomes inoperative, do not try to correct the
problem by yourself. There are no user-serviceable parts
inside. Turn the unit to the standby mode, unplug the
power plug, and please call our toll free customer
support line found on the cover of this manual to locate
an authorized service center.
Cleaning the cabinet
Wipe the front panel and other exterior surfaces of the
unit with a soft, slightly damp cloth.
Never use a solvent, thinner, benzene or alcohol to clean
the unit. Do not spray insecticide liquid near the unit.
Such chemicals may discolor the surface or damage the
unit.
Cleaning discs
When a disc becomes dirty, clean it with a cleaning cloth.
Wipe the disc from the center to out. Do not wipe in a
circular motion.
Do not use solvents such as benzine, thinner,
commercially available cleaners, detergent, abrasive
cleaning agents or antistatic spray intended for analog
records.
Cleaning the disc lens
If this unit still does not perform properly although you
refer to the relevant sections and to
“Troubleshooting”
in
this manual, the laser optical pickup unit may be dirty.
Consult your dealer or an authorized service center for
inspection and cleaning of the laser optical pickup unit.
Disc handling
Handle the discs so that fingerprints and dust do not
adhere to the surfaces of the discs.
Always store the disc in its protective case when it is not
used.
Note that discs with special shapes (heart-shaped discs,
octagonal discs, etc.) cannot be played back on this unit.
Do not attempt to playback such discs, as they may
damage the unit.
IR signal check
If the remote control is not working properly, you can use
an AM radio or digital camera (including a cellular phone
with built-in camera) to see if it is sending out an infrared
signal.
•With an AM radio:
Tune the AM radio to a
nonbroadcasting frequency. Point the
remote control towards it, push any
button and listen. If the sound from
the radio flutters, it is receiving the
remote control’s infrared signal.
•With a digital camera
(including built-in cell phone
cameras):
Point a digital camera towards the
remote control. Push any button on the
remote control and look through the
digital camera. If the infrared light
appears through the camera, the remote
control is working.
General
Signal system NTSC color
Power requirements 120 V AC, 60 Hz
Power consumption 22 W (standby: 0.5 W)
Dimensions (width x height x depth) 17.2 × 2.4 × 12.0 inches (435 x 59 x 303 mm)
Weight 6.7 lbs. (3.0 kg)
Operating temperature 41°F (5°C) to 104°F (40°C)
Operating humidity Less than 80 % (no condensation)
Terminals
Rear
Video output
RCA jack x 1 1 Vp-p (75)
Component video output
RCA jack x 3 Y: 1 Vp-p (75) P
B/CB: 700 mVp-p (75) PR/CR: 700 mVp-p (75)
HDMI output
HDMI jack x 1 Video: 480p, 720p, 1080i, 1080p, 1080p24 / Audio
Audio output (Analog)
RCA jack x 2 L/R: 2 Vrms (output impedance: more than 1k)
Audio output (Digital)
RCA jack x 1
Optical jack x 1
500 mVp-p (75)
Digital connector
Note
The specifications and design of this product are subject to change without notice.
Maintenance
I
NTRODUCTION
C
ONNECTIONS
P
LAYBACK
F
UNCTION
S
ETUP
OTHERS
E5K40UD_EN.book Page 47 Wednesday, December 24, 2008 11:15 AM