Filter
Top Products
36
Characteristics Chart
10 20 50 100 200 500 1k 2k 5k 10k 20kHz
0°
180°
10 20 50 100 200 500 1k 2k 5k 10k 20kHz
0°
180°
10 20 50 100 200 500 1k 2k 5k 10k 20 kHz
PM-SUBn
PM0.4n
10 20 50 100 200 500 1k 2k 5k 10k 20kHz
PM-SUBn
PM0.5n
10 20 50 100 200 500 1k 2k 5k 10k 20kHz
Output sound pressure level measured in the anechoic room
The LOW-PASS FREQ. control knob adjusts the frequency curve as shown in the graph below. The
characteristics are measured with PM-SUBn in sole use.
•PM-SUBn Output sound pressure level characteristics •PM-SUBn setting
Characteristic
Characteristic
Characteristic
The graphs below show the characteristics when PM-SUBn is connected to PM0.4n and PM0.5n. Setting the
PM-SUBn SUBWOOFER VOLUME and LOW-PASS FREQ. at the position below achieves the best sound
performance indicated by the thick line in the graph. The output sound pressure varies depending on room
acoustic characteristics and the PM-SUBn/main speaker system installation position. Referring to the setting
example, set the best volume position so that the low frequency output from both PM-SUBn and the main speaker
system is coordinated.
•PM0.4n + PM-SUBn characteristics •PM0.5n + PM-SUBn characteristics
•PM0.4n volume setting: Max •PM0.5n volume setting: Half
•PM-SUBn setting •PM-SUBn setting
About switching PHASE
The sound pressure level varies between the 0º and 180º PHASE SW position. In a normal environment, setting
the PHASE SW at 0º rather achieves a flat characteristic. However, depending on an installation position and a
distance between PM-SUBn and the main speaker system, there is a case that setting the PHASE SW at 180º
realizes a smoother reproduction from low to high frequency region.
•PM0.4n + PM-SUBn phase characteristics •PM0.5n + PM-SUBn phase characteristics
(1.2)
300
300
333 31
364
Main Features
Specifications
Dimensions
Active sub woofer with a closed cabinet optimized for PM0.4n
The enclosure volume is downsized by 25% comparing to PM0.5SUB (MK2). This allows PM-SUBn to install
more flexibly. With the closed cabinet, you do not have to pay attention to the bass-reflex enclosure duct direction.
A long-stroke 20-cm speaker unit exclusively designed as a sub woofer
A light BKP (Bleached Kraft Pulp) and strong Kevlar fiber mixed material is used for the cone paper of the
speaker. Also a highly durable, light and high internal-loss SBR system foamed rubber is used for the speaker
surrounding.
A closed wooden cabinet with a shining front baffle painted in glossy-black and optimized stiffness establishes
a high-quality sound reproduction.
Driving a sub woofer with 68W high-power amplifier
The RCA pin and phone are employed for the INPUT/THRU OUT jacks. The stereo RCA pin cable (1.5 m),
stereo mini - RCA pin cable (1.5 m) and 2 x phone - phone cables (2 m) are provided as standard accessories.
Without purchasing extra cables, you can connect PM0.4n/PM0.5n and PC with PM-SUBn. The volume,
cross-over frequency (50 ~ 150 Hz) and the phase (0º or 180º) can be adjusted for your usage environment.
PM-SUBn can be used for various applications such as DTM and home theater.
●Type : Sub woofer with built-in power amplifier
●Amplifier Section
•Rated Output : 68 W
•Input Sensitivity : 100 mV
•Input Impedance : 20 kΩ or more (No signal is connected to THRU OUT.)
•Output Terminal (THRU OUT) : ø6 mm TS phone jack, RCA pin jack
•Functions : Phase switch (0°/180°), cross-over frequency adjustment (50 ~ 150 Hz),
volume
●Speaker Section
•Type : Closed type acoustic suspension
•Speaker Unit : 20 cm cone type (simplified magnetic shield)
•Impedance : 8 Ω
●Power : AC120 V / 60 Hz, AC230 V / 50/60 Hz, 60 W
●Dimensions : 300 (W) x 301.2 (H) x 364 (D) mm
●Weight : About 11.6 kg
●Standard Accessories : Stereo RCA pin cable (1.5 m), stereo mini - RCA pin cable (1.5 m),
white phone - phone cables (2 m), red phone - phone cables (2 m)
Product improvement may warrant a change of specifications, newer materials or cosmetics. Changes in specifications and
features may be made without notice or obligations.