Filter
Top Products
11
ENGLISH
• Each push of the
y
PLAY/PAUSE (13) button
switches between playback and pause.
y
PLAY/PAUSE (13) button illuminates solid green
during playback and flashed in pause.
• When the
y
PLAY/PAUSE (13) button is pushed
during play, the DN-S1000 pauses playback at that
point. Push
y
PLAY/PAUSE (
13) button once
again and playback resumes.
• Playback will pause when SCRATCH is selected
with the
!8
DISC MODE button and the scratch disc
is held with your hand. Playback resumes when
your hand is released.
5
BASIC OPERATION
Play and pause
1
2
Push the
@9
PITCH/KEY
button to PITCH LED lights up.
• PITCH → KEY (key adjust) → OFF
0
Move the
@8
Pitch slider to adjust
the pitch. The current pitch setting
is displayed on the display.
Pitch decreases
Pitch increases
PITCH/KEY
RANGE
• When the i CUE button is pushed during playback,
the track stops and returns to the original position of
which playback started from, the (Cue point). This
function is also called Back-Cue. With the Back-Cue
function, you can start from exactly same position.
The i CUE button illuminates solid red when DN-
S1000 is ready to start playback.
• You can set and change Cue point as follows.
• When you started playback.
• Track select finished.
• manual search.
Play and Cue
• If you would like to start playback other from the
beginning of the track, you need to move Cue Point
using fast Search and manual search function.
• With Pitch slider you can adjust the playback speed
(Pitch).
• If you would not prefer to change key of sound, use
the Key Adjust function.
Adjusting the pitch
3
DN-S1000 has five pitch ranges,
4%, 10%, 16%, 24% and 100%.
When the
@9
RANGE button
is pushed for more than 1 sec,
the pitch range can be selected
with the
@3
PARAMETERS
knob.
4
After you found your
preferred Cue point, push
the
i
CUE button then a
new Cue point is set.
2
Push the
!8
DISC MODE
button to set
o
Scratch
Disc to search mode. The
!8
DISC MODE button
LEDs will turn off.
3
Turn the
o
Scratch Disc to
change Cue point. You can hear
the short sound of the current
Cue point.
When
o
Scratch Disc is turned in the pause,
Cue or frame repeat mode, it works as the
manual search function.
CUE/STUTTER
CUE
• With PITCH BEND function you can change pitch
temporary. DN-S1000 has two ways for this
function PITCH BEND buttons and Scratch Disc.
Pitch Bend
1
[PITCH BEND +/– buttons]
• Push the
@6
PITCH BEND
– or
@7
+ button for
momentary change of
pitch.
While holding these buttons down, the pitch
continues to change up to the limitation.
• After releasing the PITCH BEND buttons,
playback pitch returns to slider setting.
[Scratch Disc]
• When the disc mode is set to
SEARCH/BEND with the
!8
DISC
MODE button, the playback speed
can be changed by turning
o
Scratch Disc during playback.
PITCH BEND
2
:
O
F
F
ON
:
DI
SC
M
O
D
E
S
EAR
C
H
/
BEND
SC
RAT
CH
• Turn the
@3
TRACK knob.
• By pushing
@3
TRACK knob down while turning, the
tracks will increment 10 at a time.
Select the track
!
Move the Cue point
1
You can move to the approximate playback
start position by
@4
or
@5
FAST SEARCH
buttons.
[QUICK JUMP]
• If the FAST SEARCH button
is tapped shortly, the
playback position jumps about 10 seconds.
The jump time can be selected in the
preset mode from 10,20,30 or 60 sec.
[FAST SEARCH]
• When the FAST SEARCH button is pressed
and held in, the disc is fast-searched.
Power on play
• When “POWER ON PLAY” is set to “ON” at “⁄4
PRESET (10)”, playback starts from the first track
on the disc when the power is turned on.
Q
UICK JUM
P
FA
S
T
S
EAR
CH
PITCH/KEY
RANGE
3
• When the
@3
PARAMETERS
knob is pushed the pitch
range is entered and the
pitch range selection mode
is cancelled.
MP3 SEARCH MODE
PARAMETERS
PUSH
TRACK SEARCH