Filter
Top Products
12
ENGLISH
9
OTHER FUNCTIONS
1. Program play
• Up to 25 tracks from one disc can be programmed.
• Programs for up to 3 discs (one program per disc) can be stored in the non-volatile memory of each drive
for later recall. (Up to 6 discs are available.)
2
Input Program (Prog.In)
Input the program for program playback.
q Turn the track select knob o
to select the track.
w Push the track select knob o
to input the selected track to
the program.
4
Start Program Play (Prog.On)
• When “Prog.On” is selected, DN-D4000 will
cue up at the first track in the program.
• Program playback starts when
the PLAY/PAUSE
13 button
!1 is pushed.
6
Store Program (ProgM.Set)
• When “ProgM.Set” is selected, the
program that has been set is stored in the
non-volatile memory.
5
Cancel Program mode (Prog.Off)
• When “Prog.Off” is selected, the program
play mode turns off and returns to normal
play mode.
Change Program (Chang Tr)
w Turn the track select knob o
on step 3– q.
Push the track select knob o
again to return step 2– q.
★1 Insert Tracks to Program
• You can insert tracks to the previously
programmed tracks.
• One track can be inserted at
a time using the PITCH
BEND + button !2 and
return step 2– q.
★2 Clear Tracks from Program
• You can clear tracks from the previously
programmed tracks.
• One track can be cleared at a
time using the PITCH BEND
– button !2.
• Push the MEMO/PRESET
button @4 to end the program
input mode, then proceed to
Start Program Play (Prog.On).
1
Program mode select
q In the Cue or pause mode,
push the MEMO/PRESET
button @4 for more than 1
second to select preset mode.
When the MEMO/PRESET button @4 is
pushed at this time, the program mode is
selected.
✽ The mode switches in the following
order each time the MEMO/PRESET
button @4 is pushed (short push): preset
mode → program mode → off.
w Turn the track select knob o
to select the various program
setting modes as follows.
Prog.In, Prog.On, Prog.Off,
ProgM.Cal, ProgM.Set,
ProgM.Clr
The mode is entered by
pushing the track select knob
o.
Depending on conditions,
some modes cannot be
selected.
e Push the MEMO/PRESET
button @4 again to exit
program mode.
Add Program (Add Prog)
q Push the track select knob o
again to return step 2– q.
• Repeat these steps to input
whole program.
3-2
NOTES :
• The DN-D4000 is compatible with “MPEG-1
Audio Layer-3”, “MPEG-2 Audio Layer-3” and
“MPEG-2.5 Audio Layer-3”. It is not compatible
with MP1 or MP2 standards.
SAMPLING FREQUENCY
• When writing MP3 files on a CD-R/RW disc, set
the writing program’s format to “ISO9660 level 1”
or “ISO9660 level 2”, “Joliet” or “Romeo”. MP3
files written in other formats may not play
properly. With some writing programs it is not
possible to record in “ISO9660” format. Use an
“ISO9660” format writing program.
• Generally speaking, the higher the MP3 file’s bit
rate, the better the sound quality. With the DN-
D4000 it is recommended to use MP3 files
written with a bit rate of 128 kbps or greater.
• The writing program may change the positions of
the folders and files when writing the MP3 files
on the CD-R/RW disc, so the files may not be
played in the expected order.
• Make sure to give MP3 files the extension
“.MP3”. Files with extensions other than “.MP3”
or without extensions cannot be played. (On
Macintosh computers, MP3 files can be played by
adding the extension “.MP3” after the file name
consisting of a maximum of 8 Roman capital
letters and / or numerals when recording them on
CD-R/RW discs.)
• A maximum of 50 folders can be played on the
DN-D4000. The maximum number of files is also
150. If there are 151 files, only the first 150 are
played. (Files other than those with the extension
“.MP3” are not counted.)
• On the DN-D4000, folder and file names can be
displayed like titles. Roman capital letters and/or
numerals and “__” (underscores) are scrolled.
(However, a maximum of 63 characters can be
displayed.) In addition, folder and file names using
other symbols will not be displayed properly.
• The DN-D4000 is compatible with ID3-tag (Ver.
1.*, Ver. 2.0).
• It may not be possible to play some CD-R/RW
discs due to dirt, scratches or the disc’s
properties.
• Do not apply seals or tape to the label or signal
side of CDs or CD-R/RW discs. The glue could get
on the disc surface, making the disc get stuck
inside the set.
• The DN-D4000 is multi-session compatible.
Only music CDs can be played if the first session
is a music CD, and only MP3 files can be played if
the first session consists of MP3 files.
• The DN-D4000 is compatible with play lists.
(.m3u of WINAMP Form) (Preset functions)
MPEG 1.0
48 kHz
MPEG 2.0
MPEG 2.5
12 kHz
24 kHz
44.10 kHz
11.25 kHz
22.05 kHz
32 kHz
08 kHz
16 kHz
NOTES:
• With some writing programs it may not play
properly. In this case, please set to
“PLst=OFF”.
• Play List may require time for reading.
• The maximum number of play lists is also 150.
If there are over 150 play lists, only the first
150 are performed.
Playing folders or files
1
Load a disc containing MP3 files.
2
[ To select a folder ]
q In the standby mode, push the
TITLE/FOLDER button @3 more
than 1 second to display the
“Folder Sel”.
w Turn the select knob o to
select the folder you want to
listen to.
[ To select a file ]
q In the standby mode, push the
TITLE/FOLDER button @3 more than 1
second to display the “File Sel”.
w Turn the select knob o to select the file
you want to listen to.
3
Push the PLAY/PAUSE (13)
button !1.
✽ The display switches as follows
each time the TITLE/FOLDER
button @3 is pushed during
playback :
Folder name (The “FOLDER” indicator lights.)
File name (The “FILE” indicator lights.)
Title name (The “TITLE” indicator lights.)
Artist name (The “ARTIST” indicator lights.)
Album name (The “ALBUM” indicator lights.)
3-1