Filter
Top Products
R
L
R
L
R
INPUT OUTPUT
LRL
R
OUTPUT
L
R
L
SWITCHED
TOTAL 120W(1A.)MAX.
AC 120V 60HZ
AC OUTLETS
SAME AS LINE-VOLTAGE
SWITCHED 100W MAX.
AC OUTLET
OUTPUT
OPTICAL COAXIAL
OUTPUT
OPTICAL
IN
IN
OUT
IN IN OUT
SIGNAL
GND
DVD
EXT. INFREQ. STEP
VDP
TV
/
DBS
VCR
-
2/
V.AUX
COAXIAL
VCR
-
2/
V.AUX
MD/
TAPE
MD/
TAPE
VCR
-
1
VCR
-
1OPT.-1
OPT.-2
OPT.-3
FR
LOOP
ANT.
AM
SW
SR
ER
CD
PHONO
FL
C
SL
EL
DVD TV/DBS MONITOR
YYC
BCB CRCRYCB CR
COMPONENT VIDEO
SPEAKER SYSTEMS
AUDIO
DIGITAL
C-VIDEO
MONITOR
S-VIDEO
PRE OUT
L L
R
R L
R L
R L
R L
R L
R
FM
COAX.
75
B
R L
A
FRONT
FRONT CENTER SURROUND SURROUND
SUB
WOOFER
CENTER
SURROUNDEFFECT
MULTI/
ANTENNA
9kHz
10kHz
VOLTAGE SELECTOR
115V 230V
AC OUTLET
SAME AS LINE-VOLTAGE
SWITCHED 100W MAX.
L
R
L
R
L
R
L
R
DIGITAL AUDIODIGITAL AUDIO
DIGITAL AUDIODIGITAL AUDIO
7
ENGLISH
5
CONNECTIONS
• Do not plug in the AC cord until all connections have been completed.
• Be sure to connect the left and right channels properly (left with left, right
with right).
• Insert the plugs securely. Incomplete connections will result in the
generation of noise.
• Use the AC OUTLETS for audio equipment only. Do not use them for
hair driers, etc.
• Note that binding pin plug cords together with AC cords or placing them
near a power transformer will result in generating hum or other noise.
• Noise or humming may be generated if a connected audio equipment is
used independently without turning the power of this unit on. If this
happens, turn on the power of the this unit.
Connecting the audio components
• When making connections, also refer to the operating instructions of the other
components.
The power to these outlets is turned on and off when the power is switched between on
and standby from the remote control unit or power switch.
CD player
Connecting a CD player
Connect the CD player’s analog output
jacks (ANALOG OUTPUT) to this unit’s CD
jacks using pin plug cords.
Connecting a turntable
Connect the turntable’s output cord to the AVR-
3300’s PHONO jacks, the L (left) plug to the L jack,
the R (right) plug to the right jack.
NOTE:
This unit cannot be used with MC cartridges
directly. Use a separate head amplifier or step-up
transformer.
If humming or other noise is generated
when the ground wire is connected,
disconnect the ground wire.
Turntable
(MM cartridge)
Ground
wire
Connecting the pre-out jacks
Use these jacks if you wish to connect external power amplifier(s) to
increase the power of the front, center and surround sound channels, or for
connection to powered loudspeakers.
AC OUTLETS
• SWITCHED
(total capacity – 120 W (1 A.) – for North America model)
(total capacity – 100 W – for multiple voltage model)
The power to these outlets is turned on and off in conjunction with the
POWER operation switch on the main unit, and when the power is switched
between on and standby from the remote control unit. (Multiple voltage
model only)
No power is supplied from these outlets when this unit’s power is at standby.
Never connect equipment whose total capacity is above 120 W (1 A.) for
North America model (100 W for multiple voltage model).
NOTE:
Only use the AC OUTLETS for audio equipment. Never use them for hair
driers, TVs or other electrical appliances.
Connecting the AC OUTLTETS
VOLTAGE SELECTOR
For multiple voltage
model only
(Refer to page 5.)
AC CORD
AC 120 V, 60 Hz
(North America model)
AC 115/230 V, 50/60 Hz
(Multiple voltage model)
Connecting a tape deck
Connections for recording:
Connect the tape deck’s recording input jacks (LINE IN or REC) to this unit’s tape
recording (MD/TAPE OUT) jacks using pin plug cords.
Connections for playback:
Connect the tape deck’s playback output jacks (LINE OUT or PB) to this unit’s tape
playback (MD/TAPE IN) jacks using pin plug cords.
Tape deck or MD recorder
Route the connection cords, etc., in such a way
that they do not obstruct the ventilation holes.
MD recorder, DAT deck or other component
equipped with digital output jacks
CD player or other
component equipped
with digital output jacks
Connecting the DIGITAL jacks
Use these for connections to audio equipment with digital output. Refer to page 25 for
instructions on setting this terminal.
NOTES:
• Use 75 Ω/ohms cable pin cords for coaxial connections.
• Use optical cables for optical connections, removing the cap before connecting.
for Multiple voltage model for North America model