Filter
Top Products
DENON A
31
ENGLISH
Preset memory
• DENON and other makes of components can be operated by setting the preset memory for your make of video component. Operation is not
possible for some models, however. In this case use the learning function (see page 34) to store the remote control signals.
• For instructions on clearing the presettings stored in the preset memory, see page 37.
1
2
3
Set the slide switch to “VIDEO”.
Set the slide switch to the component to
be registered (VDP, VCR or TV).
Holding in the POWER button, press the
button for the corresponding manufacturer
in block A.
(Refer to Table 1.)
The LEARNED/TX LED flashes.
Keep the POWER button pressed in
when performing steps 3 and 4
()
AVR/AVC VIDEO
AUDIO
DVD TV
VDP VCR
CD
MD
MULTI
DECK
Flashes
4
5
Next, while holding the POWER button,
press the button for the code in block B.
(Refer to Table 1.) The operation is
completed when the button is released and
the LEARNED/TX LED lights.
To continue registering other components,
repeat steps 2 to 4.
DVD
START LEARNED/TX
SPEAKER
TUNING
BAND
TITLE
MENU/GUIDE
MODE
MEMORY
USE/LEARN T.TONE MULTI OUTPUT DVD
SET UP
RETURN
STATUS
DISPLAY
ON SCREEN
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH STEREO STEREO
INPUT MODE
ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
SYSTEM CALL POWER
VDP TUNER SHIFT
TV/DBS PHONO
VCR-1 CD
MD
/
TAPE
CHANNEL
VCR-2/V.AUX
TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD
MD
MULTI
DECK
SYSTEM
SETUP
SURROUND
PARAMETER
CH SELECT
SELECT
RC-860
123
4
SET
A / B
CALL OFF
ENTER
ON
/
SOURCE
56
789
+10
0
3
3,4
4
2
1
• This remote control unit can be used to operate components of other manufacturers without using the learning function by registering the
manufacturer of the component as shown on Table 1.
Table 1: Combinations of Personal System Codes for Different Manufacturers
“DVD”
(DIRECT)
—
—
PANASONIC
—
SONY
PIONEER
TOSHIBA
—
—
—
—
—
—
—
(STEREO)
DENON B
—
—
—
—
—
—
—
—
—
—
—
—
—
—
(EXT. IN)
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
B
A
q (DVD)
w (VDP)
e (TUNER)
r (TV/DBS)
t
y (PHONO)
u (VCR-1)
i (CD)
o (MD/TAPE)
p
(SHIFT)
(CHANNEL +)
(CHANNEL –)
(A/B)
(VCR-2/V.AUX)
DIRECT
STEREO
EXT.IN
SHIFT
CHANNEL
+
CHANNEL
–
*
Preset codes set upon shipment from the factory and when reset
“VDP”
(DIRECT)
DENON A
—
MITSUBISHI
PANASONIC
—
SONY A
PIONEER
—
—
—
—
PHILIPS
RCA
—
NAGNAVOX
(STEREO)
DENON B
—
—
—
—
SONY B
—
—
—
—
—
—
—
—
—
(EXT. IN)
DENON C
—
—
—
—
SONY C
—
—
—
—
—
—
—
—
—
B
A
q (DVD)
w (VDP)
e (TUNER)
r (TV/DBS)
t
y (PHONO)
u (VCR-1)
i (CD)
o (MD/TAPE)
p
(SHIFT)
(CHANNEL +)
(CHANNEL –)
(A/B)
(VCR-2/V.AUX)
DIRECT
STEREO
EXT.IN
SHIFT
CHANNEL
+
CHANNEL
–