Filter
Top Products
26
ENGLISH
Playing the input source
B
2 3
1 5
1
Press the button for the program source to be played.
EX 1: CD
CD
2
(Main unit) (Remote control unit)
2
Select the input mode.
To select the input mode from main unit.
• Selecting the analog mode.
Press ANALOG to switch to the analog
input.
(Main unit)
• Selecting the external input (EXT. IN) mode.
(In this case play the component connected to the “EXT.
IN” terminal.)
Press EXT. IN to switch the external
input.
(Main unit)
• Selecting the AUTO, PCM and DTS modes.
The mode switches as shown below each time INPUT
MODE is pressed.
(Main unit)
AUTO PCM
DTS
Input mode selection function
Different input modes can be selected for the different input sources.
The selected input modes for the separate input sources are stored
in the memory.
q AUTO (All auto mode)
In this mode, the types of signals being input to the digital and
analog input jacks for the selected input source are detected and
the program in this unit’s surround decoder is selected
automatically upon playback. This mode can be selected for all
input sources other than PHONO, CDR/TAPE and TUNER.
The presence or absence of digital signals is detected, the signals
input to the digital input jacks are identified and decoding and
playback are performed automatically in DTS, Dolby Digital or
PCM (2 channel stereo) format. If no digital signal is being input,
the analog input jacks are selected.
Use this mode to play Dolby Digital signals.
w PCM (exclusive PCM signal playback mode)
Decoding and playback are only performed when PCM signals are
being input.
Note that noise may be generated when using this mode to play
signals other than PCM signals.
e DTS (exclusive DTS signal playback mode)
Decoding and playback are only performed when DTS signals are
being input.
r ANALOG (exclusive analog audio signal playback mode)
The signals input to the analog input jacks are decoded and
played.
t EXT. IN (external decoder input jack selection mode)
The signals being input to the external decoder input jacks are
played without passing through the surround circuitry.
NOTE:
• Note that noise will be output when CDs or LDs recorded in DTS
format are played in the “PCM” (exclusive PCM signal playback) or
“ANALOG” (exclusive analog audio signal playback) mode. Select
the AUTO or DTS (exclusive DTS signal playback) mode when
playing signals recorded in DTS from a laser disc player.
Notes on playing a source encoded with DTS
• Noise may be generated at the beginning of playback and
while searching during DTS playback in the AUTO mode. If
so, play in the DTS mode.
•
In some rare cases noise may be generated when you preform
the operation to stop playback of a DTS-CD or DTS-LD.
EX 2: CDR/TAPE
CDR / TAPE
9
(Main unit) (Remote control unit)
B
DVD/VDP
CDPHONO
TV/DBS
VCR-1 VCR-2
SURROUND
MODE
TUNER SHIFT
REMOTE CONTROL UNIT RC-897
STATUS MUTING
T.TONE
MASTER
VOL
TITLE
DISC SKIP+
V. AUX
INPUT MODE CDR / TAPE
CHANNEL TV
CD·MD/CDR·DVD/VDP
VIDEO SELECT
SYSTEM
SET UP MENU
SELECT
RETURN DISPLAY
SURROUND
CH SELECT
VOLUME
CHANNEL
AVR/AVC
DVD/VDP
TV VCR
AUDIO
CD
MD/CDR
VIDEO
POWER
TAPE·VCR
OFF
ON
3
0
0
2
6
7
98
2
3
6
7
8
4
9
5
1
0
6
2
7
3
2
1
5
3
To select the input mode from the remote control unit.
• The mode switches as shown below each time INPUT
MODE is pressed.
AUTO PCM DTS
EXT. IN
ANALOG
8
(Remote control unit)