Filter
Top Products
DRZ9255 21
English
20 DRZ9255
English
About gain (G)
This function allows you to adjust how much the
output level is to be lowered.
●Characteristics during gain adjustment
0dB
-24dB
SUB-WOOFER LOW MID HIGH
About phase (PHASE)
The factory default setting is "NOR" (forward
phase). Try switching between "NOR" (forward
phase) and "REV" (reverse phase) and select
the setting that sounds most natural to you.
Adjusting the position (TIME ALIGN)
●About the time alignment function
This function allows you to adjust the speakers
so that any listener in the car can obtain the
same sound effect from the speakers.
∗ This item can be adjusted when the Audio mode is
the Standard mode or the Multi mode.
1. Press the [ADJ] button.
2. Press the [
] or [ ] button to select
"SOUND".
3. Press the [s] button.
4. Press the [
] or [ ] button to select "TIME
ALIGN".
5. Press the [
] or [ ] button to select "
FRONT " or " HIGH ".
∗ Select " FRONT " when the Audio
mode is the Standard mode, and "
HIGH
" when the Audio mode is the Multi mode.
6. Press the [ ] or [ ] button to select the
speaker to adjust.
* The mute function of a selected speaker can
be turned ON/OFF by pressing the [ROTARY]
knob while the speaker is selected.
Each press of the button switches the setting as
follows.
Operations Common to Each Mode
In the Standard mode:
7. Press the [ ] button. The setting value is
displayed.
8. Press the [s] button. The setting value
blinks.
9. Press the [
] or [ ] button to set the
distance from the speaker up to the listener.
∗ The adjustment range is 0 cm to 512.4 cm (in
about 0.7 cm steps).
∗ The range can be adjusted in about 7 cm
steps by holding down the [
] or [ ] buttons.
∗ For details, see "Appendix : Time Alignment
List" (page 32).
10.When you have finished the adjustment,
press the [s] button to return to the
screen in step 7. This sets the setting value.
11.Press the [
] button to return to the screen
in step 6.
12.Repeat steps 6 to 11 to adjust the position of
each speaker.
13.Press the [ADJ] button to return to the
previous mode.
Operations Common to Each Mode
Blinking
In the Multi mode:
HIGH
HIGH
MID
MID
LOW
LOW
SUB-W
SUB-W
Adjusting P.EQ
●About P.EQ (Parametric Equalizer)
This function allows you to correct in detail all
frequency levels by a smooth curve by correcting
frequencies matched to the type of your car.
∗ This can be adjusted when the Equalizer mode is
set to "P.EQ".
∗ This can be adjusted when the Audio mode is the
Standard mode or the Multi mode.
1. Press the [ADJ] button.
2. Press the [
] or [ ] button to select
"SOUND".
3. Press the [s] button.
4. Press the [
] or [ ] button to select "P.EQ".
5. Press the [
] button.
6. Press the [
] or [ ] button to select the
adjustment item.
∗ Pressing the [ROTARY] knob while the L/R channel
is selected turns the mute function of the selected
channel ON/OFF.
Each press of the button switches the setting as
follows.
P.EQ ON/OFF: ON/OFF
P.EQ LEFT/RIGHT: Left channel/Right channel
BAND: band (1 to 5)
fo: frequency (BAND 1,2,3 : 50 Hz to 20 kHz)
G: gain (-12 dB to +12 dB)
Q: Q-curve (0.5 to 12.0)
C: copy
(BAND 4,5 : 630 Hz to 20 kHz)
7. Press the [s] button. The setting value
blinks.
8. Press the [
] or [ ] button to adjust the
setting.
9. When you have finished the adjustment,
press the [s] button to return to the
screen in step 6. This sets the setting value.
10.Repeat steps 6 to 9 to adjust each of the
adjustment items.
11.Press the [ADJ] button to return to the
previous mode.