CONTROL DESCRIPTIONS
ATTENTION! Each subwoofi.r has speaker-level and _e-levd input
connections¢chooseonly one optionfor hook-up. DO NOT USE
BOTH INPUT CONNECTIONS AT THE SAME TIME!
The following (numbered) comrols arelocated on the subwoofer's rear
panel, as shown in Figures 1and 2.
(!) LINE-LEVEL INPUT: Stereo line-level inputs to subwoofer. Use
these RCA jacks to connect audio signals from line-level outputs from
an AN receiver/preamp/processor. (seefigure 3 & 4,j_r hook-up)
(_) SPEAKER-LEVEL INPUT: Stereospeaker-levelinputs to
subwoofer. Use theseterminalswhen line-levelconnections are not
availablefromA/V receiver/preamp/processor.
(seefigure 5,fir hook-up)
(_) VOLUME CONTROL: Controls volume levelofsubwoofer. Use
to balance the outputof the subwooferwith the main speaker output.
@ CROSSOVER FREQUENCY: The crossovercontrol allowsyou m
adjust the upper limit of the subwoofer's frequencyresponsefrom 40
to 120Hz. The subwoofer'sresponsewill begin rolling offabove the
set frequency. Set the CROSSOVER FREQUENCY tothe lower
value listed in the main speaker manual.
(_) SPEAKER-LEVEL OUTPUT: Audio loop of stereohigh-level
(SPEAKER-LEVEL)inputs. Use m loop (continue) signalto speaker
connections to the leftandright main speakers.
(seeflgure 5,for hook-up)
_) LINE-LEVEL OlYl'PUT (LW-10/12*, HT-S10MI2A): Useto loop
the full-rangeline-levd signalback to the receiver/preamplifier/amplifier
fordistribution to mainspeakers. Referto theowner's manual provided
with yourreceiver/preamplifier/amplifier.(seefigure 4,fbr hook-up)
0 LINE-LEVELOUTPUT (HT-SI5A & LW-15*): Use toloop
signal back tothe recdver/preamplifiedamplif]erfordistribution to the
main speakers. Usethe Line-Levd Output ifyou wish to filterlow
frequenciesoutof the signalgoing to yourmain speakers. Referto the
owner'smanual provided with your receiver/preamplifier/ampl_er.
(seefigure3, j_r hook-up)
®
®
@
®
@
@
PHASE: Compensates for havingsubwoofer and main speakersin
different locations. Ideally,subwoofer sound should reachthe
listening position at the sametime assound from the main speakers.
However, if thedistance from the listening position to the
subwoofer, and fromthe listeningposition to the main speakers
differ, the sound fromeachwill reach your earsat different times.
The PHASE controldelays the signal 180 degrees,so the subwoofer
output will blend with that oftbe main speakers. Slidethe PHASE
switch to "180." At the listeningposition, listen to the midbass
output. If itsounds weak,set PHASE back to "0."
POWER LED: Powerindicatorlamp. Glows greenin "AUTO
ON" mode ifaudio signalispresent. Glowsred in both "OFF"and
"AUTO ON "modes if receivingAC power, andaudio signalisnot
present afterapproximately20 minutes.
POWF_: Two-position power switch. In the "AUTO ON" mode,
the subwoofer's amplifierisautomaticallyactivated ifanaudio signal
is present andwillautomaticallybecome inactive whenthere is no
audio signalpresent afterapproximately20 minutes. In the "OFF"
mode, power isshut offto the amplifier.
VOLTAGE SELECTION (LW-X Models only): User-switchable
voltageselectionfor usewith 115 or 230 volt AC. Auentiom A//
suhomofermndds comefrom thefactorypreset to 115 volts. To select
adifferent voltage,usea flat-headscrewdriverto reposition the switch
to the desiredvoltage. WARNING: Severedamage may mult from
improperlysekcted voltage.Make sw_ youknow the voltage
requirement of tl_ _untry you arein beforeattempting to connect
this mhomofer toACpower. Obwrveproperfuse rating (typeand
value)@for sde_cd voltage®.
POWER CORD RECEPTACLE: Connect IEC cord to this
receptacle. If the cord supplied doesnot fitart availableAC outlet,
purchasethe correctAC cord from your audio dealeror an electrical
supply store.
REPLACEABLE FUSE: Protectssystem from overload,replace
with fuserating as indicated on amplifier panel at fuse location.
o o
@
O
?
&
o@ ® o ® o
Figure1. Connectionpandj_rthe HT-S15AandLW-15/15X.
Figure2 ConnectionpandfortheHT-SlOA, HT-S12A, LW-lO/lOX
andLW-12/12X
4 * Designates LW or LW-X model.