Filter
Top Products
Banner Engineering Corp. 9714 10th Ave. No., Minneapolis, MN 55441 Telephone: (763) 544-3164 FAX (applications): (763) 544-3573
WARRANTY: Banner Engineering Corporation warrants its products to be free from defects for one year. Banner Engineering Corporation will repair or replace,
free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not
cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied.
Modulated
Amplier
Logic Functions Used with (Input) Full Description
Module
Model
NONE (ON/OFF)
4-input logic gate:
AND, NOR, X-NOR
Latch or alternate-action
ip-op
NONE (ON/OFF)
Banner high-performance
remote sensors
Banner SP100FF modu-
lated xed-eld sensor
ONE-SHOT
MICRO-AMP logic
modules are designed to
accept the output signal
from a MICRO-AMP
amplier and process
that signal for a required
logic function. MICRO-
AMP logic modules
themselves contain no
amplier.
YES
ON-delay or OFF-delay
NONE (ON/OFF)
Banner SP100 Series min-
iature modulated remote
sensors
Banner catalog or
data sheet 03523
Banner catalog or
data sheet 03341
MA3A
MA3-4 and MA3-4P
MA4-2
MA4G
MA4L
MA5
MPC3
(for printed circuit
board mounting)
YES
YES
Banner catalog or
data sheet 03350
Banner catalog or
data sheet 03351
Banner catalog or
data sheet 03352
Banner catalog or
data sheet 03353
Banner catalog or
data sheet 03336
Other MICRO-AMP
®
Modules
Switches, contacts, or
NPN (current sinking)
output of dc sensors or
ampliers, including:
Banner MULTI-BEAM,
MAXI-BEAM, VALU-
BEAM, MINI-BEAM,
and ECONO-BEAM
sensors; plus MAXI-
AMP and MICRO-AMP
modules.
The MPS-15 Series power supplies are designed specically to supply power for the
Banner MICRO-AMP series ampliers and logic modules. They are constructed on small
PC boards that are track-mountable for compatibility with other track-mounted MICRO-
AMP components. The MPS-15 includes a socket for a MICRO-AMP amplier or logic
module having current sinking (NPN) output*. The combination of an MPS-15 series
power supply and a MICRO-AMP module makes a complete and compact sensing and/or
control system.
A built-in 5-amp rated SPDT output relay is supplied for easy interfacing to an external
load or circuit. Its action is controlled by the outputs of a MICRO-AMP module which is
plugged into the on-board module socket*. A switch on the PC board selects which module
output (normally open or normally closed) will activate the relay.
Two models are available. Model MPS-15 is for 120V ac operation. Model MPS-15-230
is for 220/240V ac power. Up to three MICRO-AMP modules may be powered by one
MPS -15 or MPS-15-230 power supply. A 4-inch (10cm) long mounting track is included
with each supply. Optional 6-inch (15cm) track model TR100-6 neatly accomodates the
MPS-15 Series PC board plus the PC boards of two additional RS8 sockets to form a
complete three-module MICRO-AMP sensing/logic system. (See Mounting Track infor-
mation, page 3.)
*Do not plug MICRO-AMP modules with PNP (current sourcing) outputs ("P" sufx) into the socket on the MPS-15 or MPS 15-230 power supply.
MPS-15 and MPS-15-230 Power Supplies
WARNING MICRO-AMP
®
Systems do NOT include the self-checking redundant circuitry necessary to allow their use in
personnel safety applications. A sensor or amplier failure or malfunction can result in either an energized or a de-energized output
condition.
Never use this product as a sensing device for personnel protection. Its use as a safety device may create an unsafe condition which
could lead to serious injury or death.
Only MACHINE-GUARD and PERIMETER-GUARD Systems, and other systems so designated, are designed to meet OSHA and
ANSI machine safety standards for point-of-operation guarding devices. No other Banner sensors or controls are designed to meet these standards, and
they must NOT be used as sensing devices for personnel protection.