Filter
Top Products
INPUT
CH. SEL.
0
10
TREBLE
0
10
MIDDLE
0
10
BASS
0
10
LEVEL
CLEAN CHANNEL
8 9
10
11
12
13
14 15
16
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
17
18
19
20
21
GAIN SW.
0
10
LEVEL
0
10
TREBLE
0
10
MIDDLE
0
10
BASS
OVERDRIVE CHANNEL
0
10
GAIN1
0
10
GAIN2
0
10
CONTOUR
FFRROONNTT PPAANNEELL VVIIEEWW
CAUTIONCAUTION
RISK OF ELECTRIC SHOCKRISK OF ELECTRIC SHOCK
DO NOT OPENDO NOT OPEN
ARNING:
TO REDUCE THE RISK OF FIRE
R ELECTRICALSHOCK, DO NOT EXPOSE
HIS EQUIPMENT TO RAIN OR MOISTURE
AUTION - TO REDUCE THE RISK OF FIRE,
EPLACE ONLY WITH THE SAME TYPE OF FUSE.
BRIDGE
STEREO
30
31
32
33
34
35
LEFT
RIGHT
MINI LOAD
TOTAL 8 OHM
MONO
MINI LOAD
TOTAL 4 OHM
MINI LOAD
TOTAL 4 OHM
GND
LIFT
36
37
RREEAARR PPAANNEELL VVIIEEWW
3
(13) Overdrive Channel Level: Controls the complete
signal of the overdrive channel.
(14) Overdrive Channel Treble: Adjusts the amount
of high frequency boost or cut as desired in the
overdrive channel.
(15) Overdrive Channel Middle: Adjusts the amount
of mid frequency boost or cut as desired in
overdrive channel.
(16) Overdrive Channel Bass: Adjusts the amount of
low frequency boost or cut as desired in overdrive
channel.
(17) Gain Switch: Selects Gain 1 or Gain 2 in O.D.
channel.
(18) Contour: Adjusts the overall tone quality of Gain
2 channel. Low Contour setting emphasize middle
frequency. A higher setting will notch the mid-
range to produce the crunch sound characteristic
in most heavy metal sound.
(19) Gain 2: Adjusts the amount of distortion in Gain 1
channel (LED for Gain 2 indicates when Gain 2
channel is in use).
(20) Gain 1: Adjusts the amount of distortion in Gain 1
channel (LED for Gain1 indicates when Gain 1
channel is in use).
(21) Input: Connects the electric guitar.
(30) Mono Speaker Jack: Connects the external
speaker mono signal at with a minimum impedance
of 8 ohms.
(31) Bridge switch: Switches amplifier to bridge mode
(32) Stereo switch: Switches amplifier to stereo
(33&34) External Speaker Jacks: Connects the external
speaker(s) with a minimum impedance of 4 ohms.
(35) Ground-Lift: Remove ground from the circuit to
eliminate excessive 60 cycle hum.
(36) Fuse Holder: Contains primary fuse
(37) AC Inlet: Connects AC power cord.
Do not attempt to service the LG-200AS by
yourself. Refer all servicing to a B-52
Authorized dealer. Service is required when
the LG-200AS has had liquid spilled on it or
has been damaged in any way, the amplifier
has been exposed to rain or moisture, does not
operate normally or has been dropped.
AMPLIFIER PRECAUTIONS
To reduce the risk of fire or electrical shock, do not expose
this unit to rain or moisture. Do not operate your
LG-200AS near a pool or other standing water. Make sure
all blades on the polarized power plug are fully inserted
into the power source. Ensure the powercord is not
stretched, pinched or otherwise abused. Ensure the
power cord is routed to avoid foot traffic. Your LG-200AS
amplifier should be cleaned only with a dry cloth.
WARNING: SHOCK HAZARD!