Filter
Top Products
Printed in CHINA 811-990591-010
LISTENING TO THE RADIO
1. Set the FUNCTION switch to select "RADIO".
2. Press BAND button to select the desired band AM (MW) or FM.
3. Press TUNING buttons to turn the station.
To tune faster
Hold down the TUNING button. While the button is being held, the
frequency will change faster.
To search for a station quickly (AUTO Search)
Keep the TUNING's or button pressed until the tuner starts searching
for a station. After tuning in to a station, the search stops.
To stop the Auto Search manually, press the TUNING's or button.
* The Auto Search may not stop at stations with very weak signals.
To turn off the RADIO
Press OFF button or set the FUNCTION switch to "CD".
Presetting RADIO station
You can tune into a stored station directly by entering the preset number.
10 stations on FM band can be preset.
10 stations on AM (MW) band can be preset.
1. Set the FUNCTION switch to select "RADIO".
2. Press BAND button to select the desired band AM (MW) or FM.
3. Press TUNING buttons to tune your required station.
4. Press MEM (Memory) button.
The "PGM" indicator will flash in the display window.
5. Select a preset number (M1 ~M5+) button, or press the PRESET
button to select preset number.
6. Press MEM (Memory) button to store the station.
7. Repeat steps 2 to 6.
To select a numbered button from M6 to M10.
First press the M5+ button, then press one of numeric buttons.
Tuning into a preset station
Press the preset number (M1~M5+) button.
Or press the PRESET button to select preset number.
For better reception
NOTE:
* The FM "STEREO" indicator lights up when the tuned-in station is
broadcasting in stereo and the reception is good.
1. Set the FUNCTION switch to select " CD".
2. Open the CD door with the OPEN button.
3. Insert the CD with the printed side facing upwards and push the disc
gently until it clicks so that the disc fits into the pivot.
4. Press the CD door to close.
Note: To play an 8 cm (3-inch) disc, you can play it without an adaptor.
On display window
When you press , the display window shows:-
DISC PLAYING
During play
The track number of the current selection appears.
When " /OFF" is pressed during play, total number of tracks on the disc
will be displayed and the unit is still on. If " /OFF" is pressed again the
unit will be returned to full stop mode. If " " is pressed the unit returns
to play mode. The unit will be returned to full stop mode automatically
after approximately 30 seconds if no button is pressed.
During pause
The playing track number flashes.
When no disc is inserted onto the player and when " " is pressed, the
INTRO Play - Playing the First Ten Seconds of All the Selections
1. Press P. MODE (Play mode) during play until
" " flashes in the display window.
2. Press to begin the INTRO play.
3. Pressing P.MODE again will cease the INTRO
play and continue playback in the NORMAL
play mode.
* INTRO play always starts from the first track.
PGM (Program) Play - Playing the Selections in the Desired Order
1. Press P. MODE (Play mode) button until
PGM flash and " " in the display
window.
2. Press or to select the desired
selection.
3. Press MEM/REPEAT/ENTER button to store
this track in memory.
4. To add additional tracks, repeat steps 2 and
3.
5. Press , "PGM" stops flashing and play
starts.
To Edit Program Play:
To check: Press "MEM/REPEAT/ENTER" lightly during programming
before you press . Each time "MEM/REPEAT/ENTER"
is pressed the track number appears in the display
window.
To change: When checking press either or to alter the track
number for the program currently displayed. Press "MEM/
REPEAT/ENTER" to register the newly selected track into
memory.
To delete: When open the CD door including that program will be
cancelled.
SHUFF (Shuffle) Play - Playing the Selections in Random Order
1. Press P. MODE (Play Mode) during play until
"SHUFF" flashes in the display window.
2. Press to begin the SHUFFLE play.
* To locate the beginning of the track being
played: press .
* To locate the next track: press . However,
you cannot locate a previous track even if
you keep pressed.
Repeat Playback (Repeat One and Repeat All)
To repeat the same track
Press MEM/REPEAT/ENTER during play until
" 1" appears in the display window.
Select desired track to be played only once
by pressing or .
To repeat the whole disc
Press MEM/REPEAT/ENTER during play until
" ALL" appears in the display window.
VARIOUS PLAYING MODES
Note:
* Repeat play can be performed during program, intro and shuffle
play.
* The program is also erased when the disc compartment is opened or
the auto power off function turns the power off.
* If the program mode is exited by means of the /OFF key, all the
programs would still remain in memory.
* During the program play, the AMS operates in the programed order.
(AMS-auto music sensor)
The Digital Anti-Shock System incorporates a special electronic circuit
that prevents sound from skipping when the unit is subjected to shocks
and vibration during play.
When you start playback, the Anti-Shock System turn on and " "
indicator appears in the display to prevent sound skipping.
DIGITAL ANTI-SHOCK SYSTEM
When the unit receives a physical shock which prevents the laser pick-up
from "reading" the CD, this system immediately starts playing the sound
stored in its memory and continues until the laser pick-up recovers.
If the unit is subjected to continuous shocks and all the data stored in
memory is used up the sound will skip.
If the vibration stops then the data memory will be restored. If continuous
vibration is applied when the data memory is empty, an error message
" " will be displayed. To reset the CD player press " /OFF" once.
To cancel the Anti-Shock System, press the ANTI-SHOCK button, then
" " indicator disappears in the display
NOTES:
In the "DIGITAL ANTI-SHOCK SYSTEM", battery power consumption
is more because the disc rotates faster than normal and the memory
circuit is active.
When the Digital Anti-Shock System is switched on or off, the sound
will be interrupted for a short time. This is normal.
Should any problem persist after you have made the following checks,
consult your nearest service facility.
Disc play does not start:
The disc is inserted upside down or incorrectly. Insert the disc
correctly with the label surface up Dusty or defective disc Dirty or
dusty lens. The disc compartment lid is not closed Moisture
condensation -> Leave the unit in a warm place until the moisture
evaporates The AC power adaptor is not plugged into the wall outlet
The unit is not placed on a level surface Weak batteries
No sound from the headsets:
The headphones/earphone plug is not firmly connected to the PHONES
jack Adjust the VOL control Dirty plug
No sound from the connected speakers:
Check the connections The amplifier is not turned on
Skipping of sound:
Dirty or defective disc Dirty lens. Strong vibration
When using with batteries the battery life is short:
Manganese batteries are used. Use alkaline batteries
Display window shows " " error message and the unit cannot
be operated:
No disc , dirty disc or scratched disc. The unit will return to full stop
mode after approx. 30 seconds, or reset the player by pressing "STOP"
once and then insert a disc to start playing.
TROUBLESHOOTING GUIDE
Output (at 1KHz 0dB level) Line output (stereo minijack)
Output level 0.4V (Rms) at 47KΩ at 1KHz
Headphones/earphone (stereo minijack)
15 mW + 15 mW at 16Ω to 32Ω
Power requirements 2 size AA (LR6 or UM-3) alkaline batteries,
or
DC IN 6V, 450mA power adaptor
Polarity of plug
Operating voltage: U.S.A., Canada:
(AC adaptor) 120V AC 5% 60 Hz
Middle East and Australia:
240V AC 5% 50 Hz
UK and Germany:
230V AC 5% 50 Hz
Chile: 230V AC 5% 50 Hz
Singapore, Malaysia & Thailand:
200-240V AC 5% 50 Hz
Japan: 100V AC 5% 50/60Hz
Frequency range: FM 87.3 - 108.1 MHz
AM 520 - 1720 KHz
Dimensions: Approx. 132 x 147 x 38 mm (w/h/d)
Weight: Approx. 290g (not incl. batteries)
Cleaning the unit
Do not use volatile chemicals on this unit. Clean by lightly wiping with a
soft cloth.
Cleaning CD
If the CD skips or will not play, the disc may need to be cleaned.
Before playing, wipe the disc in a circular motion from the centre
out with a cleaning cloth. After playing, store the disc in its case.
Handling the disc
Only touch the CD on the edge to avoid finger prints on its surface. Do
not stick paper or tape nor write anything on the surface.
General
Compact disc digital audio system
Digital filter two-time oversampling
Three-spot optical pick up
Design and specifications are subject to change without notice.
MAINTENANCE
SPECIFICATIONS
To improve FM reception:
extend the headphone cord.
To improve AM (MW) reception:
rotate the unit.
Pause mode of the second track
First track playing begins
Notes on
During playback (batteries are in use), is on.
When the battery voltage level is low, will flash. 10~15 minutes,
playback still continues in this period.
Playback will automatically come to a stop when the batteries have no
more power. Do not repeat pressing as the unit may operate
incorrectly. Replace all the batteries with new ones.
will not be on if an AC adaptor is used.
Using on house current
If the unit you purchased does not include an AC power adaptor, please
use a 6V 450mA AC power adaptor. Otherwise use only the supplied
AC power adaptor.
Be sure to disconnect the AC power adaptor when the unit is not in use.
During playback, every time the P. MODE (PLAY MODE) key is pressed,
the mode will change to the next one as follows:
NORMAL play -> INTRO -> PGM (PROGRAM) -> SHUFFLE
Normal Play - Playing the Whole Disc
The CD is played once from beginning to end.
POWER SOURCES
display window shows " "
The unit cannot be operated when no disc message is displayed. After
approx. 30 seconds the unit will return to full stop mode, or reset the
player by pressing " /OFF" once and then insert a disc to start playing.
Under some conditions, noise may be heard or sound skipping may
occur.
-when the disc is dirty or scratched.
-when the disc contains certain signals.
-when the unit is subjected to a certain kind of shock.
In these conditions, try to release "DIGITAL ANTI-SHOCK SYSTEM."