Filter
Top Products
MADE IN USA
SIX YEAR WARRANTY
AN-130+ Speaker Monitor Owners Manual
AN-130+ TECHNICAL SPECIFICATIONS
(Specifications Subject to Change Without Notice)
ANCHOR AUDIO CUSTOMER SERVICE
800.262.4671
FOR ADDITIONAL INFORMATION
visit www.anchoraudio.com
7
HAVING TROUBLE WITH YOUR SOUND SYSTEM?
CONDITION POSSIBLE CAUSE
No Sound
(Power LED Not Lit)
• turn POWER switch on
• plug in power cord
No Sound
(Power LED Lights)
• check for output from source
• make sure all cables are completely plugged in
• increase volume control
• press mute button on remote
(AN-130RC+ only)
• turn power switch to off then back to on
(AN-130RC+ only)
Distorted Sound • check input cable connection
• lower input signal level
Excessive Hum or Noise • use shielded input cables
HAVING TROUBLE WITH YOUR WIRELESS SYSTEM?
(Wireless Model Only)
No Sound • confirm transmitter power switch is set to on
• turn up volume control
• plug microphone into body-pack transmitter
• turn sound system on
• replace mic/transmitter battery
• make sure hands free mic cable is fully plugged into transmitter
• turn off mute by pressing, volume up/down or mute
(AN-130+RC only)
Frequent Transmitter Dropouts • replace mic/transmitter battery
• move mic/transmitter closer to AN-130+
• change transmitter to different channel
Rated Power Output 30 watts continuous
Max SPL @ Rated Power 103 dB @ 1 meter
Frequency Response 65 Hz – 18 kHz ± 3 dB
Speaker Type 4.5” woofer, 10 mm dome tweeter
AC Power Reqs. 110 – 125 VAC, 50/60 Hz
50W max
Export Model 208 – 240 VAC, 50/60 Hz
50W max
Fuse Rating T 1.0A / 250V
Export Model T 0.5A / 250V (internally mounted)
Dimensions (HWD) 5.25” x 8.4” x 9”
(13 x 21 x 23 cm)
Weight 8.5 lbs / 3.8 Kg
Inputs
Line Hi-Z, unbalanced, 1/4” & 1/8” jack
Microphone Lo-Z, unbalanced, 1/4” jack
Output
Line Lo-Z, buffered, 1/4” phone
Sensitivity For Rated Output
Line -20 dBV (100 mVrms)
Microphone -43 dBV (7.5 mVrms)
General Warning or Caution
Electric Shock
Protective Conductor Terminal
European Union CE Mark European Union CE Mark
The Exclamation Symbol in the figure above appears in Warning and Caution
tables throughout this document. This symbol designates an area where
personal injury or damage to the equipment is possible.
The Electrical Shock Symbol in the figure above appears throughout this manual.
This symbol indicates a hazard arising from dangerous voltage. Any mishandling
could result in irreparable damage to the equipment, and personal injury or
death.
The Electrical Shock Symbol in the figure above appears throughout this manual.
This symbol indicates a hazard arising from dangerous voltage. Any mishandling
could result in irreparable damage to the equipment, and personal injury or
death.
The presence of the CE Mark on Anchor equipment means that it has been
designed, tested and certified as complying with all applicable European Union
(CE) regulations and recommendations.
Electrical Shock Symbol
Figure Protective Conductor
Terminal Symbol
Waste Electrical and Electronic Equipment (WEEE)
This symbol on the product or on its packaging indicates that this product
must not be disposed of with regular waste. Instead, it is the user responsibility
to dispose of waste equipment according to the local laws. The separate
collection and recycling of the waste equipment at the time of disposal will help
to conserve natural resources and ensure that it is recycled in a manner that
protects human health and the environment. For information about where the
user can drop off the waste equipment for recycling, please contact your local
Anchor representative. See Section for instructions on how to disassemble the
equipment for recycling purposes.
Figure WEEE Directive Symbol