Filter
Top Products
GENERAL FEATURES (Cont.)
25
24
29 30
26
27
28
31 32
33
36
35
34
37
13&14.TRACK
(Track Buttons) -
These buttons are used
to select the track to be played. FORWARD SKIP
& BACK SKIP.
15. TIME
(Time Button)
-
The TIME button switches
between ELAPSED PLAYING TIME,
REMAINING TIME in a selection and TOTAL
REMAINING TIME of the disc.
16. PITCH SLIDER -
The pitch can be changed up to
+/- 12% by Pressing the PITCH BUTTON so the
PITCH LED is lit, then moving the sliding fader.
The pitch will not be changed if the PITCH LED is
off.
17. BPM BUTTON -
Switches the mode of the
display between showing the BPM and the
percentage change in PITCH. Use COUNTER
BUTTON
18. COUNTER BUTTON -
Tap this button with the
beat of the music to determine the current Beats
Per Minute (BPM).
19. REALTIME CUE –
This allows you to set the CUE
POINT without stopping the play back. This button
also sets the beginning of a seamless loop.
20. CUE -
Pressing the CUE button during play
provides a return to the position at which play was
started. If PAUSE is used before CUE or CUE
POINT was set, that will become the cue point.
Alternately pressing the PLAY button and the
CUE button allows the CD to be played from the
same position any number of times. The CUE
LED will light up from the time the Cue button
is pressed until the CD has reset to the position at
which play was started. Steady lighting of this
LED indicates the ready condition.
21. OUT / EXIT -
Used to set the ending point when
looping music. The player will start to loop
continuous. Until you press this button again to
exit. This is not a seamless function.
22. START/PAUSE
(Play/Pause Button) - Each press
of the PLAY/PAUSE BUTTON causes the
operation to change from play to pause or from
pause to play.
23. RELOOP BUTTON -
If a LOOP has been made,
and you have hit the exit button, press this button
to enter the loop again. To exit loop press
OUT/EXIT button.
B. LCD
26.PLAY INDICATOR (
) -
The PLAY indicators light
during playback.
27.PAUSE INDICATOR (
) -
The PAUSE indicators
light during pause or cue mode.
28.A-B INDICATOR –
These light when player
performs repeat A-B playback.
29.PROGRAM INDICATOR -
This lights when
program mode is set or played.
30.REPEAT Indicator -
(REPEAT 1, REPEAT ALL)
These light during repeat one or all playback.
28,31,32.TRACK, MINUTE, SECOND –
These
Displays information on the current track and time.
33.PITCH OR BPM DISPLAY -
Show either beat per
minute or percent of pitch adjustment.
34.BPM INDICATOR -
Lights up when BPM Button is
engaged.
35.PITCH INDICATOR-
Lights to show percent of
pitch is displayed.
36.ELAPSED & TOTAL REMAIN INDICATORS
–
These indicate that the time shown on the display
is the ELAPSED, TOTAL remaiming or SINGLE
song remaining time.
37.LOOP, RELOOP –
displayed when loop is
engaged LOOP flashes when playing loop.
D.MAIN UNIT REAR PANEL
LINE OUT 1 and 2 –
The audio signals from each
player are output from these jacks.
REMOTE
- Connect this connector to the control unit
using the included control cords..
DIGITAL -
connect to Minidisc or CDR device.
VOLTAGE SELECTOR –
(multi-vlotage models only)
On multi- voltage models, use this to select the
power voltage. Always disconnect the power plug
before changing the voltage.
E.CONTROL UNIT REAR PANEL(FIGURE 4)
CONNECT TO MAIN UNIT –
Connect this connector
to the REMOTE connector on the main unit using
the included control cords.
CONTROL –
Connect this connector to the control out
from mixer control out. Available on future mixers.
American audio • DCD-PRO300™ INSTRUCTIONS MANUAL • PAGE 7