Filter
Top Products
TROUBLESHOOTING TIPS
TOTAL AUDIO POWER: 50 Watts (26 Watts RMS)
Frequency Response: 40 Hz - 20 kHz
Inputs: Front
Signal to Noise Ratio @ 1 kHz input: >65 dB
System THD (distortion): < 0.5 % THD @ -10dB full
scaleinput voltage
SATELLITE AMPLIFIED SPEAKERS
Speaker Drivers (per Satellite): Two 1" (28 mm) micro drivers
SUBWOOFER
Speaker Drivers: Two 4" (102 mm) drivers
POWER REQUIREMENTS
USA/Canada/and applicable 120v 60Hz AC
Latin American countries:
Europe/United Kingdom; 230v 50Hz AC
applicable Asian countries;
Argentina, Chile and Uruguay:
ETL / cETL / CE / NOM / IRAM Approved
Find more troubleshooting tips in the FAQs located in the Customer
Support area of our web site: www.alteclansing.com.
Q. When connected to my computer sound card, should I use the
Windows volume control to adjust the volume of my speakers?
A. No. Adjust the Windows controls to about center as a starting
point and then use the speaker controller to adjust volume control. If
the volume is turned too high on the sound card, it can distort the
sound.
Q. One, and sometimes both of my speakers do not work.
A. Check the input cable from speaker to the audio source and make
sure that it is connected to the line-out jack, which is the un-amplified
source. Make sure all the cables are plugged in correctly and have a
good connection. Still not working? Then try unplugging the cable
from the back of the computer, and insert the stereo plug into the
headphone jack of an alternate source (e.g., Walkman, Discman or FM
radio) and play music. If the speakers work, you may need to adjust
your volume and balance controls in your audio source, or Windows, if
connected to your computer's sound card
Q. My speakers give off a crackling sound (or static, or other noise).
What could be wrong?
A. Check all cables and make sure that they are connected to line-out
or audio-out jack on your sound card or other audio source, and NOT
speaker-out. If your audio source is your computer, check the volume
control in Windows: make sure that it is not set more than halfway.
Setting this level too high can cause sound distortion. If this does not
stop the noise, unplug the cable from the audio source and use an
alternate source (e.g., Walkman, Discman or FM radio) by plugging the
stereo cable into the headphone jack. If the noise goes away, you may
have a problem with your audio source.
Q. What can cause radio feedback?
A. If you are living near a radio tower you could have interference
caused by radio frequency. Try moving your speakers to see if the
interference goes away; if not, you may be able to purchase a stereo
cable from your local retailer that has a higher percentage of
shielding.
Q. Can I hook my speakers to my TV or Stereo?
A. Yes, as long as your TV or Stereo has an unamplified source which
is line-out (check your TV or Stereo owners manual). These speakers
may be used with any audio device that has a stereo headphone jack.
You may also need a cable that has RCA jacks on one end and a 1/8
inch stereo connector at the other end (these may be purchased at
most local electronics stores).
Q. I have very little bass coming from my Subwoofer. How do I
increase the bass output?
A. Adjust the BASS control through your audio sound source
(computer sound card control, CD player control, etc.). Check to make
sure that all of your cables are hooked up correctly and are making a
good connection.
Q. I have a low hum coming from my Subwoofer. Is this normal?
A. Yes. The AC in your house is at 60 cycles per second, which is
within the audio frequency of your subwoofer. Some low hum is
natural and can be detected when your speaker system is powered on
without source audio playing, or when volume is set at an extremely
low level.
Q. I have a loud hum coming from my Subwoofer. What should I do?
A. Move the power cord from the power surge protector (if
applicable) and plug directly into an AC wall outlet. Move your cables
and check to see that they are making a good connection. If you
disconnect your stereo cable from the audio source and the loud hum
goes away, then you may need to adjust the volume control in your
audio source as you may be overdriving the volume settings on your
speaker system. If you are using your 2100 speakers with your
computer system, just click on the speaker icon located next to the
digital clock to the lower right of your Windows 9X or 2000 screen and
adjust the volume.
Q. When I put my Subwoofer on my desk my monitor distorts. Why?
A. The Subwoofer is not magnetically shielded, and this can cause
distortion if it is less than 3 feet from your monitor.
Q. Where should the volume control be set on my Subwoofer?
A. Start with it in the center position then adjust to your preference.
Q. The DIN connector from the controller has multiple pins on one end,
and when trying to attach this cable I noticed that some of the pins are
bent, so I am not able to insert the cable into Subwoofer. What should I
do?
A. Try to gently straighten the pins with tweezers or very small pliers.
If this does not work, then contact the Altec Lansing Consumer
Support Department for further instructions.
SPECIFICATIONS
4