A SERVICE OF

logo

Open as PDF
next previous
©TitanToolInc.Allrightsreserved. 3
Maintenance
Follow all safety precautions as described in the Safety
Precautions section of this manual before proceeding.
NOTE: Refer to the Parts List section in this manual for part
identication.
Replacing/Servicing the Seal Assembly
Ifyourspraygunleaksorspitsatthetipwhenyoureleasethetrigger,the
needleorseatisworn,damaged,ordirtyandmustbereplacedorcleaned.
Never attempt to perform maintenance on the spray gun
without first performing the “Pressure Relief Procedure.”
1. Disconnectthesprayhosefromthegun.
2. Removethetipandtipguard.
3. Withthetriggerdepressed,removethediuserfromthefrontofthe
gun.
4. Removethereversiblecarbideseatfromthediuserbygently
tappingthediuseronahard,atsurfaceuntiltheseatdropsout.
5. Usingasmallat-bladescrewdriver,removethegasketfromthe
diuser.
6. Usinga3/16”socketwrench,removetheballvalveassemblyfromthe
sealassembly.
7. Installthenewballvalveassembly.
8. Reversethecarbideseatandplaceitontheballvalveassemblyinthe
retaining nut housing.
9. Placethegasketaroundthecarbideseat.
10. Withthetriggerdepressed,threadthediuserontotheretainingnut
housing. Tighten with a wrench.
Servicing the Needle Assembly
1. Performsteps1–6ofthe“Replacing/ServicingtheSealAssembly.”
2. Loosenandremovethelocknut,rearhousing,andretractorpinsfrom
thebackofthegunhead.
3. Removethesealassemblyfromthegunheadbygentlytappingon
thebackofthesealassembly.
4. Soakthepartsintheappropriatesolventandwipeclean.
5. Inspectthepartsforwearandreplace,ifnecessary,duringreassembly.
NOTE: Lubricate all packings and moving parts before
reassembly with a lithium-based grease.
6. Reversesteps1–3toreassemble.
Replacing/Removing the Filter
1. Pulldownonthebottomofthetriggerguardandswingitawayfrom
the handle.
2. Slideothehandleandunscrewthehandletubefromthegunhead.
3. Unscrewthelterfromthegunhead.Ifthelterbreaksoduring
removal,useasmallwoodscrewtoremoveremnantsfromthegun
head.
NOTE: The lter has left-handed threads. Turn the lter
clockwise to remove.
4. Screwtheneworcleanedltercounterclockwiseintothegunhead.
5. Slidethehandletubeoverthelterandscrewitintothegunhead.
6. Slidethehandleoverthehandletubeandreattachittothegunhead.
7. Securethetriggerguardbackinpositiononthebottomofthehandle.
Filter Chart
Part
Number
Application Filter Type Color of
Filter Body
500-200-15 Syntheticresin,enamels,clean
varnishes,stains,azures
Extrane red
500-200-10 Basecoatenamels,primer
enamels,llers,markingpaints,
textured enamels
Fine yellow
500-200-06 Emulsions,latexpaints,acrylic
paints
Medium white
500-200-03 Fillerpaints,largeareasurfaces Coarse green
Accessories
Part # Description
651-070 6”GunExtension
651-071 12”GunExtension
651-072 18”GunExtension
651-073 24”GunExtension
611-630 GunExtensionSwivelHeadAssembly.
310-383-1 3’PoleExtension
310-386-1 6’PoleExtension
711-600 PoleExtensionSwivelHeadAssembly.
316-505 1/4”x50’AirlessHose,3300PSI
310-110 Spray/RollAccessoriesKit
310-150 3’PolewithInnerFeedRoller
310-160 3’PolewithSprayRoller
002-XXX FlatTips
661-XXX SC-6ReversibleTips