A SERVICE OF

logo

Open as PDF
next previous
Connecttheprojector’sACpowercordintoanAC
outlet.ThePOWERindicatorturnsred.Openthelens
cover.
PressthePOWERON/STAND-BYbuttononthe
remotecontrol.ThePOWERindicatorbecomesgreen
andthecoolingfansstarttooperate.Thepreparation
displayappearsonthescreenandthecountdown
starts.
2
3
1
Thepreparationdisplaydisappearsafter30seconds.
4
Afterthecountdown,theinputsourcethatwas
selectedthelasttimeandtheLampmodestatusicon
(seepage46)willappearonthescreen.
IftheprojectorislockedwithaPINcode,aPINcode
InputDialogBoxappears.EnterthePINcodeas
instructedbelow.
Seepage46fortheLampmode.
Video
Selected Input Source and Lamp Mode
Completeperipheralconnections(withacomputer,
VCR,etc.)beforeturningontheprojector.
Lampmodestatus
OK
AftertheOKicon
disappears,youcan
operatetheprojector.
PIN Code Input Dialo� Box
Turnin� On the Projector
Enter a PIN code
SelectanumberbypressingthePoint▲▼buttons,and
thenpressthePoint►buttontofixthenumberandmove
thepointer.Thenumberchangesto"".Ifyoufixedan
incorrectnumber,movethepointertothenumberyouwant
tocorrectbypressingthePoint◄button,andthenselect
thecorrectnumberbypressingthePoint▲▼buttons.
Repeatthissteptocompleteenteringafour-digitnumber.
"1234"issetastheinitialPINcodeatthefactory.
Afterenteringthefour-digitnumber,movethepointerto
"Set"bypressingthePoint►button.PresstheSELECT
buttonsothatyoucanstarttooperatetheprojector.
IfyouenteredanincorrectPINcode,"PINcode"andthe
number()turnsred.EnterthecorrectPINcodeall
overagain.
What is PIN code?
PIN(PersonalIdentificationNumber)codeisasecuritycode
thatallowsthepersonwhoknowsittooperatetheprojector.
SettingthePINcodepreventsunauthorizeduseofthe
projector.
APINcodeconsistsofafour-digitnumber.RefertothePIN
codelockfunctionintheSettingMenuonpages47–48for
lockingoperationoftheprojectorwithyourPINcode.
Note:
• When the Input Search function is set on
On1 or On2, the input signal will be searched
automatically (p.44).
• When the Logo select function is "Off,” the
logo will not be displayed on the screen
(p.42).
• When the "Countdown off" or "Off" is selected
in the Display function, the countdown will not
be shown on the screen (p.41).
• During the countdown period, all operations
are invalid.
• If the PIN code number is not entered within
three minutes after the PIN code dialog box
appeared, the projector will be turned off
automatically.
• The “1234” is set as the initial PIN code at the
factory.
CAUTION ON HANDLING THE PIN CODE
If you forget your PIN code, the projector can no
longer bestarted.Take aspecialcare in settinga
newPINcode;writedownthenumberinacolumn
on page 70 of this manual and keep it on hand.
ShouldthePINcodebemissingorforgotten,consult
yourdealerorservicecenter.
18
PIN code
PIN code
Basic Operation
16
Note:
The Filter warning and Lamp replacement
icons may appear on the screen depending on
the usage state of the projector.