Philips TP2781, TP3281, TP3681 Manual

A SERVICE OF

next previous

USING THE SMART LOCK (BLOCK CHANNEL) CONTROL

SLEEP

POWER

AV ON/OFF POSITION FREEZE

TV

VCR

ACC

SWAP SOURCE PIP CH

UP

DN

SMART

SOUND

SMART

PICTURE

MENU

SURF

VOL CH

MUTE

CC STATUS CLOCK A/CH

EXIT

TV/VCR

RECORD MEDIA

INCREDIBLE

VCR MULTI

1

2

FEATURES

SmartLock

.

.

.

BLOCK CHANNEL

SETUP CODE

.

.

FEATURES

TIMER

SmartLock

DNR

INCR. PICT.

PIP

.

.

.

.

.

BLOCK CHANNEL

SETUP CODE

.

.

FEATURES

PICTURE

SOUND

FEATURES

INSTALL

TIMER

SmartLock

DNR

INCR. PICT.

PIP

.

.

.

TIMER

SmartLock

DNR

INCR. PICT.

PIP

.

.

.

.

.

.

.

TIME

ACTIVATE

CHANNEL

TUNER

.

.

.

.

.

FEATURES

SmartLock

.

.

.

BLOCK CHANNEL

SETUP CODE

.

.

.

.

----

Enter current

access code

FEATURES

SmartLock

.

.

.

BLOCK CHANNEL

SETUP CODE

.

.

.

.

xxxx Code correct

FEATURES

SmartLock

.

.

.

BLOCK CHANNEL

SETUP CODE

.

.

.

.

CHANNEL 22

ALLOWED

Select channel

Please press > to

block viewing

FEATURES

SmartLock

.

.

.

BLOCK CHANNEL

SETUP CODE

.

.

.

.

CHANNEL 22

BLOCKED

Select channel

Please press < to

allow viewing

6

5

4

3

7

8

.

.

CHANNEL 22

Blocked by Smartlock

XXXX

Please enter access code

or select another channel

All channels can be viewed

until the TV is turned off.

CHANNEL 22

Blocked by Smartlock

- - - -

Please enter access code

or select another channel

STEREO

Note: You can also block out the use of the A/V external inputs on the rear of the TV.

This stops the viewing of VCR, DVD, etc., programs which can be shown through the

A/V Input jacks. Select AV 1, AV 2, or SVID-R, MM1, MM2, MM3, and select block.

A

fter your personal access code

has been set (see previous

page), you are now ready to select

up to 5 channels or inputs to block

out or censor.

Press the MENU button on the

remote to show the on-screen menu.

PICTURE will be highlighted.

Press the CURSOR DOWN ■

button twice to select the FEA-

TURES menu.

Press the CURSOR RIGHT

ᮣᮣ button and the menu will

shift to the left, then CURSOR

DOWN

■

to highlight the SMART

LOCK control.

Press the CURSOR RIGHT

ᮣᮣ button again to shift the dis-

play left, the BLOCK CHANNEL

control will be highlighted.

Press the CURSOR RIGHT

ᮣᮣ button. “---- Enter current

access code” will appear within the

menu.

Enter the correct access code

number. “XXXX” shows on the

SETUP CODE display as you press

the NUMBER buttons. “XXXX

Code correct” will appear.

Press the CHANNEL (+) or

(–) buttons (or NUMBER but-

tons) to select the channel you want

to block.

Press the CURSOR RIGHT

ᮣᮣ button to block viewing of

the channel, or the CURSOR

LEFT ᮤᮤ button to allow viewing

of the channel.

Repeat steps 5 through 7 for any

other channels you wish to block

from viewing.

BEGIN

UNBLOCKING CHANNELS

Access the blocked channel direct-

ly by using the number buttons on

the remote control.

Enter your four digit access code.

All blocked channels will be view-

able until the TV is turned off. When

the TV is turned back on, the blocked

channels will not be viewable.

Any channel that has been

blocked will be skipped

when the Channel (+) and

(–) buttons are used to scan

all available channels. To

view a blocked channel,

press the number buttons

on the remote to directly

access the channel and

refer to the Unblocking

Channels section below.