30
23
24
25
26
27
28
29
36
35
32
34
33
28
27
26
31
30
29
HORN SWITCH:
SPEAKON OUTPUT:
JACK OUTPUT:
PRE AMP OUT:
XLR DIRECT INJECT:
DI SELECT:
FX LOOP PRE EQ:
FX LOOP POST EQ:
FOOTSWITCH:
Activates the on board COMPRESSION DRIVER. Not present on DB150H.
SPEAKON connector for connecting external speaker cabinet. Total minimum impedance of
enclosure connected to this socket must be no lower than 8 Ohm (4 Ohm DB400C/H) when used in conjunction with
another cabinet either connected to jack socket (25) or linked from the cabinet connected to the speakon connector. If
only a single enclosure is to be used the minimum impedance should be no lower than 4 Ohm. Not present on DB150C
JACK socket for connection of external speaker enclosure. See above.
Provides output to drive external power amplifier.
XLR socket for output of low impedance balanced line signal. Provides signal for use with
external mixing desks or PA system
Selects whether the signal sent to the XLR DIRECT INJECT is derived from a PRE EQ signal or a
POST EQ signal.
SEND & RETURN jacks for connection of external effects. Effects units connected to this set
of send and return sockets receive a PRE EQ signal. Should be used in conjunction with any effect which is going to
radically alter the sound of the amplifier, such as Octave dividers, distortion pedals etc.
SEND & RETURN jacks for the connection of external effects. An effect unit(s) connected to
this set of send and return sockets will recieve a POST EQ signal. Should be used in conjunction with effects such as
chorus, flanger or any type of digital pedal.
Should be used for connecting the correct type of footswitch to allow the remote switching of the
following features. DB150C & DB150H, FS2 for switching of GRAPHIC and INPUT MODE.
DB300C/DB300H/DB400C/DB400H, FS5 for switching of INPUT MODE/PRE SHAPE/GRAPHIC and
COMPRESSOR
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVERS. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
MADE IN THE UNITED KINGDOM BY BLT INDUSTRIES LTD.
SUPPLY VOLTAGE ~230V T1A
TO REDUCE THE RISK
TO REDUCE THE RISK OF
FIRE HAZARD REPLACE FUSE WITH
SAME TYPE AND RATING ONLY.
REMPLACER LE FUSIBLE
PAR LE MEME ET LE CALIBRE.
DEBRANCHER A LA PRISE
SECTEUR AVAVT D'OUVRIR.
CONSUMPTION 300 WATTS ~50 - 60 Hz.
& FUSE RATING ~115V T2A
RAIN OR MOISTURE.
NOT EXPOSE THIS APPLIANCE TO
OF FIRE OR ELECTRIC SHOCK DO
WARNING
CAUTION
ATTENTION
ATTENTION
CE
CAUTION
WARNING
THIS EQUIPMENT MUST BE EARTHED.
MAXIMUIM POWER
A TOTAL LOAD OF NO LESS THAN 8 OHMS
CAN BE CONNECTED AT ANY ONE TIME.
PIN -1 = GND.
PIN +1 = SIG.
SPEAKER OUTPUT
HORN
OFF
8P-86
DIRECT INJECT
SERIAL No:
PREAMP OUT
FX LOOP
FX LOOP
SEND SEND
PRE EQ.
POST EQ.
RETURN RETURN
FOOTSWITCH
PRE/POST
EQ
SEND SEND
PRE EQ.
POST EQ.
FX LOOP
FX LOOP
RETURN RETURN
FOOTSWITCH
DIRECT INJECT
PRE/POST
EQ
SPLIT
LO
HI
LEVEL
HI OUT
LO OUT
POWER AMP IN
PREAMP OUT
SUPPLY VOLTAGE ~230V T6.3A
& FUSE RATING~115V T10A
TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK DO
NOT EXPOSE THIS APPLIANCE TO
CAUTION
TO REDUCE THE RISK OF
FIRE HAZARD REPLACE FUSE WITH
SAME TYPE AND RATING ONLY.
REMPLACER LE FUSIBLE
PAR LE MEME ET LE CALIBRE.
DEBRANCHER A LA PRISE
SECTEUR AVAVT D'OUVRIR.
WARNING
THIS EQUIPMENT MUST BE EARTHED.
SERIAL No:
MAXIMUIM POWER
CONSUMPTION 500 WATTS ~50 - 60 Hz.
ELECTRONIC CROSSOVER
SPEAKER OUTPUT
CE
MID
PIN -1 = GND.
PIN+1=SIG.
OFF
LO
HI
HORN
8P-8687
5
4
3
2
1
-0+-0+
1
2
3
4
5
WARNING
RAIN OR MOISTURE.
ATTENTION
ATTENTION
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVERS. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
MADE IN THE UNITED KINGDOM BY BLT INDUSTRIES LTD.
A TOTAL LOAD OF NO LESS THAN 8 OHMS
CAN BE CONNECTED AT ANY ONE TIME
CAUTION
23
31
24
25
REAR PANEL FEATURES
DB150C & DB150H
DB300C, DB300H, DB400C & DB400H
}
Laney
4
DB BASS MANUAL
