Beko WMB 71031 PTM Manual

A SERVICE OF

next previous

13

EN

Starting the programme

Press Start / Pause button to start the programme.

Programmefollow-uplightshowingthestartupof

the programme will turn on.

C

 Ifnoprogrammeisstartedornokeyis

pressed within 1 minute during programme

selection process, the machine will switch

to Pause mode and the illumination level of

the temperature, speed and loading door

indicatorlightswilldecrease.Otherindicator

lightsandindicatorswillturnoff.Oncethe

Programme Selection knob is rotated or

any button is pressed, indicator lights and

indicators will turn on again.

Child Lock

UseChildLockfunctiontopreventchildrenfrom

tampering with the machine. Thus you can avoid

any changes in a running programme.

C

 IftheProgrammeSelectionknobisturned

when the Child Lock is active, "Con" appears

on the display. The Child Lock does not

allow any change in the programmes and the

selected temperature, speed and auxiliary

functions.

C

Even if another programme is selected with

the Programme Selection knob while the Child

Lock is active, previously selected programme

will continue running.

To activate the Child Lock:

Press and hold 1

st

and 2

nd

Auxiliary Function

buttons for 3 seconds. The lights on the 1

st

and

2

nd

Auxiliary Function buttons will flash, and

"C03","C02","C01"willappearonthedisplay

respectively while you keep the buttons pressed

for 3 seconds. Then, "Con" will appear on the

display indicating that the Child Lock is activated.

IfyoupressanybuttonorturntheProgramme

Selection knob when the Child Lock is active,

same phrase will appear on the display. The lights

on the 1st and 2nd auxiliary function buttons that

are used to deactivate the Child Lock will blink 3

times.

To deactivate the Child Lock:

Press and hold 1

st

and 2

nd

auxiliary function

buttons for 3 seconds while any programme is

running. The lights on the 1

st

and 2

nd

Auxiliary

Functionbuttonswillflash,and"C03","C02",

"C01"willappearonthedisplayrespectivelywhile

you keep the buttons pressed for 3 seconds.

Then,"COFF"willappearonthedisplayindicating

that the Child Lock is deactivated.

C

 Inadditiontothemethodabove,todeactivate

the Child Lock, switch the Programme

SelectionknobtoOn/Offpositionwhenno

programme is running, and select another

programme.

C

Child Lock is not deactivated after power

failures or when the machine is unplugged.

Progress of programme

Progress of a running programme can be followed

fromtheProgrammeFollow-upindicator.At

the beginning of every programme step, the

relevant indicator light will turn on and light of the

completed step will turn off.

You can change the auxiliary functions, speed

and temperature settings without stopping the

programme flow while the programme is running.

To do this, the change you are going to make must

beinastepaftertherunningprogrammestep.If

the change is not compatible, relevant lights will

flash for 3 times.

C

 Ifthemachinedoesnotpasstothespinning

step,RinseHoldfunctionmightbeactive

or the automatic unbalanced load detection

system might be activated due to the

unbalanced distribution of the laundry in the

machine.

Loading door lock

There is a locking system on the loading door of

the machine that prevents opening of the door in

cases when the water level is unsuitable.

Loading door light will start flashing when the

machine is switched to Pause mode. Machine

checksthelevelofthewaterinside.Ifthelevelis

suitable,LoadingDoorlightilluminatessteadily

within1-2minutesandtheloadingdoorcanbe

opened.

Ifthelevelisunsuitable,LoadingDoorlightturns

offandtheloadingdoorcannotbeopened.If

youareobligedtoopentheLoadingDoorwhile

theLoadingDoorlightisoff,youhavetocancel

the current programme; see "Canceling the

programme".

Changing the selections after

programme has started

Switching the machine to pause mode

Press the Start / Pause button to switch the

machine to pause mode while a programme is

running. The light of the step which the machine

isinstartsflashingintheProgrammeFollow-up

indicator to show that the machine has been

switched to the pause mode.

Also, when the loading door is ready to be opened,

LoadingDoorlightwillalsoilluminatecontinuously

in addition to the programme step light.

Changing the speed and temperature settings

for auxiliary functions

Dependingonthesteptheprogrammehas

reached, you may cancel or activate the auxiliary

functions; see, "Auxiliary function selection".

You may also change the speed and temperature

settings; see, "Spin speed selection" and

"Temperature selection".

C

 Ifnochangeisallowed,therelevantlightwill

flash for 3 times.

Adding or taking out laundry

Press the Start / Pause button to switch the

machinetopausemode.Theprogrammefollow-