Filter
Top Products
NATURAL SOUND AV RECEIVER RX V2095 RDS
CINEMA DSP
7ch
VOLUME
INPUT SELECTOR
INPUT MODE
l6
20
28
40
60
l2
8
4
2
0
–dB
PHONES
BASS
EXTENSION
BASS TREBLE BALANCE
TONE
BYPASS
VIDEO AUX
EFFECT
A/B/C/D/EA
SPEAKERS
B
PROGRAM
PRESET STATIONS
TUNING
EXT. DECODER
STANDBY/ON
55
4
3
2
l
0
l
2
3
4
LR
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
EDIT
FM/AM
EON
MEMORY
MODE START
PRESET
/TUNING
RDS MODE
TUNING
MODE
MAN’L/AUTO FMAUTO/MAN’L MONO
PTY SEEK
VCR 2
VIDEO AUX
REC OUT
VCR 1
TV/DBS
PHONO
TUNER
CD
DVD/LD
SOURCE
TAPE/MD
45
English
1
2 Press and hold the MEMORY button for more than 3
seconds
After approx. 5 seconds, the automatic preset tuning begins
from the currently displayed frequency toward higher
frequencies. Received stations are programmed to A-1,
A-2 ... A-8 sequentially.
* If more than 8 stations are received, they are also
programmed to the preset station numbers on other groups
(B, C, D and E) in that order.
If you want to store the first station received by the
automatic preset tuning to the desired preset station
number;
If, for example, you want to store the first received station to
C-5, select “C-5” by using the A/B/C/D/E (
1) button and the
PRESET STATIONS/TUNING (
2) button after the MEMORY
button is pressed in step 2. (These operations must be done
before the automatic preset tuning begins.)
The first received station is stored to C-5, and next stations to
C-6, C-7 ... sequentially. If stations are stored up to E-8, the
automatic preset tuning will be finished automatically.
If you want to make the automatic preset tuning
toward lower frequencies;
In step 2, after the MEMORY button is pressed (and then the
desired preset station number is selected), press the
PRESET/TUNING (
3) button to make “ : ” go off from the
display. Then press the left side of the PRESET STATIONS/
TUNING (
2) button. (These operations must be done before
the automatic preset tuning begins.)
The automatic preset tuning begins toward lower frequencies.
Ⅵ Automatic preset tuning
You can make use of an automatic preset tuning function for RDS stations. With this function, this unit performs automatic tuning
and stores RDS stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the
manual preset tuning method on page 43.
To store stations
FM/AM
➁
➀
12
➂
BASIC OPERATION
Flashes
MEMORY
MAN’L/AUTO FM
SPEAKERS
A
TAPE/MD
CD
TUNER
PHONO
DVD/LD
TV/DBS
VCR 1
VCR 2
V-AUX
MEMORY
STEREO
AUTO
When the automatic preset tuning is finished
The display shows the frequency of the last preset station.
Check the contents and the number of preset stations by
following the procedure of the section “To recall a preset
station” on page 44.
To recall a preset station
Simply follow the procedure of the section “To recall a preset
station” on page 44.
A recalled station is shown by the frequency (and the station
name if the station employs PS data service) on the display.
Notes
●
You can replace a preset station by another FM or AM
station manually by simply following the procedure of the
section “To store stations” on page 43.
●
The automatic preset tuning search will be performed
through all RDS network frequencies until stations are
stored up to E-8. If the number of received stations is not
enough to be stored up to E-8, the search is finished
automatically after searching all frequencies.
●
With this function, only RDS stations with sufficient signal
strength are stored automatically. If the station you want to
program is weak in signal strength, tune to it in monaural
manually and program it by following the procedure of the
section “To store stations” on page 43.
* There may be a case that this function cannot receive a
station which could be received by the automatic tuning
method. This is because this function receives a large volume
of PI (Program Identification) data along with the station.