Filter
Top Products
6
BBT210S
25cm Woofer x2
Tweeter x1
Standard Monaural Phone Jack
250 Wrms
4Ω
596 x 403 x 363 mm
(23-7/16” x 15-7/8” x 14-5/16”)
21 kg (46 lbs. 5 oz)
Speaker Cable
Owner’s Manual (this booklet)
BBT110S
25cm Woofer x1
Tweeter x1
Standard Monaural Phone Jack
250 Wrms
4Ω
430 x 372 x 363 mm
(16-15/16” x 14-5/8” x 14-5/16”)
14.5 kg (31 lbs. 15 oz)
Speaker Cable
Owner’s Manual (this booklet)
Thank you for purchasing the Yamaha BBT410S/210S/110S Speaker System.
In order to get the most in performance and life out of this product, we recommend that
you thoroughly read this Owner’s Manual before using it. After reading the manual, please keep
it in a safe place for future reference.
Model
Speaker
INPUT Jack
Power Handling
Impedance
Dimensions (WxHxD)
Weight
Accessories
BBT410S
25cm Woofer x4
Tweeter x1
Standard Monaural Phone Jack
250 Wrms
4Ω
596 x 640 x 483 mm
(23-7/16” x 25-3/16” x 19”)
29 kg (63 lbs. 15 oz)
Speaker Cable
Casters x4
Owner’s Manual (this booklet)
* Design and specifications may change without notice due to improvements.
● Avoid using your amplifier and speaker in the following locations
to prevent possible damage:
•In direct sunlight or next to heating equipment.
•Extremely cold or hot locations.
•Locations exposed to high humidity or excessive dust.
•Locations subject to strong shocks or vibration.
● If one of the following occurs, disconnect the cable from the
INPUT jack as soon as possible then contact the dealer from
whom you purchased the device for repair.
•The speaker cable or plug has become damaged.
•Sound is not produced or an abnormal smell or smoke is
present.
•A foreign substance gets into the device or liquid is spilled
onto the device.
•The device is wet or damp (rain, etc.).
•An abnormality or damage is found on the device.
● Before connecting the device to a power amplifier or other
devices, make sure that the power on all devices is switched
OFF. Not doing so can damage the speaker, etc.
● When connecting the device to a power amplifier, etc., use the
supplied speaker cable or a commercially available speaker
cable (with a standard monaural phone plug). Use of a normal
shielded guitar cable, etc. can result in cable overheating or
damage.
● Disconnect cables before moving the system. To prevent short
circuits or breakage of cables, always disconnect cables prior to
moving system equipment.
● Your Yamaha amplifier is a precision musical instrument. Handle
it with care and avoid dropping or bumping it.
Precautions
● Do not apply excessive force to the switches and controls.
● To prevent damage and possibly electrical shock, never open
the case and tamper with the internal circuitry.
● Never place the device on an unstable surface, table, or sloped
surface. Also, never stack the device excessively. Doing so may
cause the device to fall or overturn, causing injury.
* If the device is to be stacked, we recommend that the casters be removed
from the amplifier/speaker to prevent overturning.
● Never use benzene, thinner or other volatile liquids for cleaning,
as these chemicals may cause damage or discoloration to the
finish. Always use a dry, soft cloth to wipe off dust and dirt.
Specifications
To protect your speakers
When choosing a power amplifier to use with your speakers,
make sure that its power output matches the speakers’ power
capacity (refer to the Specifications below). Even if the amplifier’s
power output is lower than the speakers’ power capacity, the
speakers may be damaged when clipping of a high input signal
occurs.
The following may cause damage to speakers:
•Feedback caused when using a microphone.
•Continuous high sound pressure level produced by electronic
instruments.
•Continuous high-power output distorted signals.
•Popping noises caused by turning on equipment, or by con-
necting or disconnecting system-components while the ampli-
fier is turned on.