Filter
Top Products
Printed in U.S.A. • Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601-2000 • © Winegard Company, 2006 2451964 Rev. 1/12/09
CONSUMER 90 DAY WARRANTY
The Winegard Company warrants this Winegard product against any defects in materials or workmanship within 90 (ninety) days from date of
purchase. No warranty claim will be honored unless at the time the claim is made, you present proof of purchase to an authorized Winegard dealer
(if unknown, please contact Winegard Company, 3000 Kirkwood Street, Burlington, IA 52601-2000, telephone 800-288-8094).
Winegard Company (at its option) will either repair or replace the defective product at no charge to you. This warranty covers parts, but does not
cover any costs incurred in removal, shipping or reinstallation of the product. The warranty does not extend to products which have been subjected
to misuse, improper installation, or to damage caused by wind, lightning, ice or other occurrences over which the manufacturer has no control.
The 90 Day Warranty is provided on the condition that the equipment is properly delivered with all handling and freight charges prepaid to your
Winegard dealer for return to our factory for repair or replacement. Winegard dealers will arrange for the replacement or repair and return to you
without charge the product which failed due to defective material or workmanship.
WINEGARD COMPANY WILL NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, MADE BY ANY
OTHER PERSON.
ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR
PURPOSE AND MERCHANTABILITY ARE LIMITED TO THE 90-DAY PERIOD OF THIS WARRANTY.
The foregoing shall be the sole and exclusive remedy of any person, whether in contract, tort or otherwise, and Winegard shall not be liable for
incidental or consequential damage or commerical loss, or from any other loss or damage except as set forth above.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of limitation of incidental or consequential damages,
so the above limitations or exclusions may not apply to you.
This warranty gives you specic legal rights and you may also have other rights which vary from state to state. Rev. 2/08
FM TRAP OPERATION (Not applicable to Models AP-4700, AP-4800, or HDP-269)
The preamplier features two FM traps, one xed and the other variable. The preamplier is shipped with the xed FM in the “FIXED
TRAP IN” position and the variable FM trap tuned out of the FM band (about 108 MHz). See Figure 5.
If FM reception is desired, move the FM trap switch to the “FIXED TRAP OUT” position.
FM interference is indicated by “herringbone” patterns appearing on any VHF channel (2 through 13). If this interference is present,
verify the FM trap is in the “FIXED TRAP IN” position. If interference is still present, turn the “VARIABLE FM TRAP” screw very slowly
while observing the TV channel with the greatest interference until the picture clears. See Figure 5.
The variable FM trap can also be used with the xed FM trap in the “FIXED TRAP OUT” position. This allows you to receive FM and
tune out a specic FM station that is causing interference. This is performed the same as the proceeding paragraph except the FM trap
is in the out position.
SPECIFICATION : 14 Volts Nominal at 130 Milliamps Max.
NOTE: This power supply is equipped with a Polyswitch. If there is a short between the preamp and the power supply, it will
shut the power supply off until the short is removed.
APPLY LABEL
NOTE: A label is supplied so you can enter the
installation date and record the frequency the vari-
able trap is tuned to. Once tuning is complete, apply
the label to the bottom of the preamplier to seal
openings. See gure 5. For models without traps,
apply the label to the bottom of the preamplier to
seal openings.
TIPS:
If splitting the signal to multiple TVs or combining with another signal source, it is strongly recommended that the power injector be
installed between the preamplifer and the splitter/combiner input. In this case, the cable connection from the “TV” jack of the power
injector goes to the splitter input or valid combiner input. Use splitters rated from 54-806 MHz or wider bandwidth (commonly 5-1000
MHz) for over-the-air television signal distribution.
Additional distribution/inline ampliers must be installed FOLLOWING the TV output of the power injector, NOT on the downlead cable
line connecting to the ANTENNA port. Check TV picture quality, if the power injector LED is glowing when powered, and antenna
alignment prior to adding additional line ampliers.
To maximize the operating life of the amplier, install the power injector close to the TV receiver (if only one will be used with the
antenna) or the rst signal splitter. A maximum preamp-to-power injector length of 150 feet RG-6 or 150 feet RG-59 is acceptable.
APPLY LABEL AFTER TUNING
FIG. 5
+
DUAL
INPUT
UHF
ANT.
VHF
ANT.
FIXED TRAP OUT
VARIABLE
FM TRAP
FIXED TRAP IN
TO
POWER
SUPPLY
WINEGARD COMPANY
BURLINGTON, IOWA