Wharfedale 10.5 Speaker User Manual


 
Introduction
Preparing the Subwoofer
Positioning the Subwoofer
Wharfedale subwoofers are intended for use with high quality domestic sound systems. They are equally effective in
Stereo and Home Cinema applications.Your subwoofer will probably be used in conjunction with Wharfedale
loudspeakers though they will partner any audiophile or top-quality home cinema amplification and loudspeakers.
No further preparation is necessary.
You should attach the spikes or protective rubber feet to the subwoofer.
Carefully invert the subwoofer. Protect the top by placing it
on a soft surface such as a towel. Open the protective bag
and slide it part-way down the cabinet.Two sets of
adjustable screw feet are provided - regular and spiked.
Choose one set only - do not use a mixture of spiked and
regular feet.
Screw the threaded washer over each foot as shown. Screw
a foot part-way into the threaded hole at the bottom of
each leg of the subwoofer and hand-tighten the washer.
When all four screw feet have been fitted, stand the subwoofer upright and remove the bag.
With the aid of a spirit level, screw each foot in and out until the subwoofer is
level (side to side and front to back) and firmly supported on all four feet.Tighten
the washer with a wrench to lock the assembly in position.
Note:When using spiked feet take care not to drag the subwoofer and be careful
not to pierce objects or cables which may be hidden under carpets, etc. Spikes
are not suitable for use with stone floors and can cause damage to wood floors,
so consider carefully before deciding which feet to use.
Although the unit may be placed almost anywhere in the room, we recommend that it be placed in front of the
listener and as central to the listening position as possible. There should be a mains outlet within easy reach.The
subwoofer should not be operated within 450mm of a television set as the drive unit magnet may distort the picture.
The bass unit is mounted underneath the subwoofer and moves a lot of air at high volume, so make sure the floor is
sound. Do not place the subwoofer with the bass port near surfaces or objects that may rattle.
We suggest you initially position the subwoofer about 20cm (8 inches) from the wall. Placing the unit close to the
wall will enhance the bass; placing it across the corner of the room will increase the bass further, possibly at the
expense of clarity.
Experiment with locations and sources before making a final decision.
Diamond 10. SX-SUB and 10. MX-SUB:
Diamond 10. GX-SUB:
Unpacking your Subwoofer
Before Connecting the Subwoofer
Open the carton and remove all the top packing pieces. Lift the subwoofer out taking care not to damage the
cabinet.When lifting the unit from the carton support it from the bottom. DO NOT attempt to lift the subwoofer out
of the carton using the protective bag.The unit is heavy; if you cannot manage it easily, get someone to assist you.
Switch off your amplifier and all connected source units at the mains. Unplug the power cords if necessary.
Make sure the subwoofer is disconnected from the mains and that the ON/OFF switch is OFF.
Before re-connecting your system to the AC power supply, check that all the connections are properly made.
Signal cables should be properly terminated and fully screened to minimise hum. If you connect your subwoofer
via the low level signal inputs, the cable between your control unit or processor and the subwoofer could be
quite long so screeningis particularly important. Consult your dealer if in doubt
#
#
#
#
.
Diamond 10 Subwoofers
Screw
Foot
Threaded
Washer
10
AC 220-240V~50Hz 400W
FUSE T4AL250V
AC 220-240V~50Hz 400W
FUSE T4AL250V
POWER
LEFT
LEFT
SPEAKER LEVELINPUTS
INPUT
OUTPUT
LINE LEVEL
RIGHT
RIGHT
CROSSOVER
FREQUENCY
CROSSOVER
FREQUENCY
VOLUME
0
35Hz 85Hz
45Hz 75Hz
55Hz
65Hz
10
OFF
ON
DIAMOND.10 GX-SUB
WHARFEDALE INTERNATIONAL LTD,HUNTINGDON, UNITED KINGDOM
WHARFEDALE INTERNATIONAL LTD,HUNTINGDON, UNITED KINGDOM
SERIAL No:
PHASE
180°
N21090
Connecting Your Subwoofer - 1
b
c
d
e
f
g
h
i
j
SubwooferVolume Control
Crossover Frequency Control
Phase Control
Mains Power Switch
IEC Mains Input Socket
Mains Power Fuse
Speaker Level Inputs
Line Level Inputs
Line Level Outputs
b
c
d
f
g
h
i
j
SubwooferVolume Control
Auto Power Switch
I
Phase Switch
Crossover Frequency Control
Mains Power Switch
EC Mains Input Socket
Mains Power Fuse
Speaker Level Inputs
Line Level Inputs
Line Level Outputs
USB Power Supply Port*
e
1)
1!
* Diamond 10. MX Sub only
DIAMOND 10. GX-SUB REAR PANEL
DIAMOND 10. MX-SUB REAR PANEL
INPUT
OUTPUT
VOLUME
LEFT
RIGHT
POWER
AUTO
PHASE
180°
ON
OFF
WARNING:
TO REDUCE THE RISK OFFIRE OR ELECTRICALSHOCK,
TO REDUCE THE RISK OFFIRE OR ELECTRICALSHOCK,
CAUTION:
ATTENTION:
OFF ON
DEBRANCHER AVANT DE REPLACER LE FUSIBLE,
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE,
35
45
55
65
75
85
AC220-240V 50Hz 110W
FUSE
MODEL: DIAMOND.10 SX-SUB
MODEL: DIAMOND.10 SX-SUB
WHARFEDALE INTERNATIONALLTD,HUNTINGDON,UNITED KINGDOM
WHARFEDALE INTERNATIONALLTD,HUNTINGDON,UNITED KINGDOM
CROSSOVER
FREQUENCY
SPEAKER
LEVEL
INPUTS
LINE LEVEL
SUB-WOOFERAMPLIFIER
SERIALNO.:
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE
REPLACE ONLY WITH SAME TYPE FUSE AND RATING
REPLACE ONLY WITH SAME TYPE FUSE AND RATING
UTILISER UN FUSIBLE DE RECHANGE
UTILISER UN FUSIBLE DE RECHANGE
DE MEME TYPE ET CALIBRE
DE MEME TYPE ET CALIBRE
T2AL250V
MANUFACTURE DATE:
MANUFACTURE DATE:
(Hz)
AC INPUT
AC INPUT
POWER
LEFT
RIGHT
N 21090
DIAMOND 10. SX-SUB REAR PANEL
All three subwoofers feature the same connectivity.
- a USB power supply
receiver.This receiver enables a Subwoofer to receive signals from a suitably equipped AV
amplifier or processor without the need for a signal input interconnect. Consult yourWharfedale dealer for details.
The 10. MX-Sub has one additional feature 1! for charging the internal battery of an
optional wireless
11