+
-
-
+
Requires two R03
(AAA) batteries
Operating range
Remote sensor
5m
VHF
UHF
Mixer
Rod antenna
Outdoor
antenna
(optional)
(supplied*)
Adjust to the best
possible reception
75-ohm coaxial cable
or
* 15LZJ28 only
Connect the antenna to at the
rear of the TV.
Connect the power cord to an
electrical outlet
~110V-240V, 50/60Hz
(15LZJ28)
~220V-240V, 50Hz (15LZR17 / 15LZR28)
~220V, 50Hz (15LZU28X)
Notes
• Do not connect the power cord until all
your equipments have been connected.
• The antenna cables should not be
bundled with the power cord and the like.
Insert the batteries into the remote
control.
• If the remote control does not operate
correctly, if the operating range becomes
reduced, replace both batteries with
new ones.
• When the remote control will not be used
for a long period of time or when the
batteries are worn out, remove the
batteries to prevent leakage.
• Do not drop, dampen or disassemble the
remote control.
Cautions
• Do not dispose batteries into fire. Dispose
batteries into the designated disposal
areas according to the local regulations.
• Do not mix battery types or combine used
batteries with new ones.
SAFETY INSTRUCTIONS AND MAINTENANCE
For safety
1) If and when anything abnormal occurs, unplug the power cord from the outlet immediately.
Make sure that the smoke has stopped, then contact for a service.
Continual usage of TV in such condition may cause a fire or an electric shock.
2) Do not cut, break, heat, modify, twist, bunch up or bent the cord or apply excessive force or
tension to it, as this may cause damage, fire or electric shock. Contact a service technician if
the power cord is damaged.
3) Do not pull on the power cord when removing the plug from the wall outlet. Always hold
the plug firmly when removing it. If the power cord is yanked, the cord may become
damaged and fire or electric shock may occur.
4) Do not repair, modify or disassemble the TV by yourself. Let qualified technicians check and
adjust your TV. To avoid electrical shock or fire, never modify the TV.
5) Do not place hot objects or naked flame sources, such as lighted candles or nightlights, on
or close to the TV. High temperature can melt plastic and lead to fires.
6) The TV shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the TV. This may cause a fire or electric shock.
7) Do not let metallic materials and/or combustibles get in the TV. These items may cause a
fire or an electric shock. Be especially observant when children are present.
8) Do not stand or climb on the TV. The TV is dangerous if it is broken or if it has fallen down.
Be especially observant when children are present.
9) When the TV will not be used for a long period of time, unplug the power plug from the outlet
for safety.
The main power plug or an appliance coupler is used as a disconnecting device and therefore
should be remain readily operable.
10) During lightning storm, do not touch any part of the TV, including the power cord and the
antenna lead-in-wire. You may suffer an electric shock.
2) 3) 4) 5), 6)
7) 8) 9) 10)
GETTING STARTED
Push the q (Power switch) on the
front of TV until it clicks to turn on
the power.
Refer to page section J for details on power
on and off.
Preset the channels automatically
(ASM function).
Use remote control for this operation. The
buttons on the TV with similar name may
also be used.
1 Select the starting position for channel
to be preset. Press the Number buttons
(-/--, 0~9) or CH s/t.
1
2 Set the correct broadcast system for
your region. Press MENU and then
;
-/+ to highlight the “ SET UP” icon.
B
Confirm “COLOR” is set to “AUTO” and
“SOUND” is set to proper system. (Refer
to the table on page section G.) If not,
press CH s/t to select “COLOR” or
“SOUND” and press ;
-/+ to set each
proper system.
3 Press MENU and then ;
-/+ to highlight
the “
TUNING” icon. Select “ASM”,
then press ;
+ to start the search. When
the TV screen returns to the start position,
the procedure is completed.
CH
CH
B
Press ;
-/+ to adjust the sound
volume.
SPECIFICATIONS
SAFETY INSTRUCTIONS AND MAINTENANCE (continued)
Notes on installation and on use
11) Place the TV on a horizontal, stable surface. Avoid location subject to vibration. Do not place
the TV on its side or back. Otherwise, the TV may drop or fall off which may cause injury or
damage.
12) Do not block the ventilation holes. Place the TV at least 10 cm away from the walls for good air
circulation. The inside of this TV will overheat if the ventilation holes are sealed, which may
result in a fire.
13) Take measures to prevent the TV from falling over. If not, the TV may lean or fall over and
cause an injury. When moving, watch out for the ties.
14) Avoid placing the TV in direct sunshine, near a heating source or places with a high temperature,
such as in a closed car. A fire may result when the inside temperature increases.
15) Also avoid the placing the TV on dusty or damp places. This may cause a fire or electric shock.
16) Set up the outdoor antenna away from high ways, power lines and neon signs. If the antenna
falls down or drops, it may cause injury or electric shock accidents.
The antenna should be checked and replaced periodically.
17) Do not jolt the TV, resulting in the TV falling over, dropping or causing an injury.
18) Keep magnets, electric clocks, speakers, etc. away from the TV.
19) Do not spray volatile compounds such as insecticide on the cabinet. This may cause a
discoloration or damage of the cabinet.
Notes on cleaning
20) Before cleaning, unplug the power plug.
Clean the cabinet with a soft and dry cloth.
Do not use benzine, thinner, etc. to clean the TV.
21) Sometimes disconnect the power plug from the outlet and check it.
If dust has collected on the power plug connectors, clean off the dust.
Broadcast Transmission Systems in Each Country or Region
Notes
• PAL, SECAM and NTSC3.58 are different color signal broadcast transmission systems
applicable to different country or region. NTSC4.43 (MHz) are used in some VTRs to playback
NTSC recorded video tapes through PAL television equipment.
• Refer to the Specifications table to find the receivable television systems for this TV.
Exemptions
9 Toshiba is not liable for any damage caused by natural disaster (such as thunder, earthquake),
fire, acts by third parties, accidents, misuse, or uses in other improper conditions.
9 Toshiba is not liable for incidental damages (such as profit loss or interruption in business,
modification or erasure of record data, etc.) caused by use or inability to use of product.
9 Toshiba is not liable for any damage caused by neglect of the instructions described in the
owner’s manual.
9 Toshiba is not liable for any damage caused by misuse or malfunction through simultaneous
use of this product and the connected equipment.
• The
> MONITOR terminals output the TV
program or video (A) signals being
displayed on the screen. You can record a TV
program or video signals by connecting a VTR
from the output terminals (
> MONITOR) to
the input terminals of the VTR. However,
except for personal use, you are not allowed
to use video or sound you have recorded
without consent of the owner of copyright
according to copyright law.
Notes
• Connect the equipment to either front or back
a (1) terminal. Audio and video interference
may occur if both terminals are connected.
• Do not connect one VTR to the output and
input terminals on the TV simultaneously, it
may cause interference.
• For 15LZJ28 / 15LZR28 / 15LZU28X models,
when connecting the audio signal to a
monaural equipment, connect AUDIO L or R
terminal of the TV to the AUDIO terminal of
the equipment.
• For 15LZR17 model, when connecting the
audio signal to a stereo equipment, connect
them to the L/MONO terminal of the
equipment. Otherwise, connect the audio
signal to either L or R terminal.
Color Television
OWNER'S MANUAL
Owner's Record
You will find the model number and serial number on
the back of the TV. Record these numbers in the spaces
provided below. Refer to them whenever you call upon
your TOSHIBA dealer regarding this product.
Model number:
Serial number:
©TOSHIBA CORPORATION, 2006
All Rights Reserved
15LZR 17/28
15LZJ 28
15LZU 28X
Printed in Indonesia
VX1A00014100
EXTERNAL EQUIPMENT CONNECTIONS
• You can connect video equipments such as a VTR and video camera to this TV and enjoy the
high quality picture. The front A/V terminal a (1) is convenient when hooking up video camera
or game equipment.
• The following describes how to use and connect the TV with other AV equipment. Refer to the
owner’s manual of the equipment to be connected as well.
• Connection cables are not supplied.
Caution: Do not plug in any power cords until you have finished connecting all equipment.
12) 14)
16) 20) 21)
13)
Sturdy tie
Not lean
and
protrude
TROUBLESHOOTING
Before calling service personnel, please check the following chart for a possible cause to the
trouble you are experiencing.
Symptom Solution
Power is not turned on. • Be sure the power cord is plugged in.
No sound. • The headphones may be plugged in.
Poor color/tint. • The contrast, color and tint may need to be adjusted.
• If you change the direction of the TV while the TV is on, the picture
may suffer from color shading. If so, turn off the TV and allow
about 30 minutes to cool, then turn on the TV again. The picture
may be improved.
Spots appear on the • The broadcast signal may be jammed by other electrical sources
screen. such as cars, motorcycles, electric trains, high tension lines, neon
signs, hair dryers.
Lines appear on the • The broadcast signal may be jammed by other TV receivers,
screen. personal computers, and TV games, as well as interference from
radio stations.
Double or triple images. • Interference may be due to broadcast waves reflected from
mountains or buildings.
• Check if the direction of the antenna has changed due to strong wind.
Snowy picture. • The antenna lead may be broken or disconnected.
• Check if the direction of the antenna has changed.
Remote control does • The batteries in the remote control may be exhausted.
not work. • The batteries may be improperly installed.
• Check that there is no obstruction between the remote control and
the remote (infrared) sensor.
• Check that a strong light is shining on the remote (infrared) sensor.
• Check that the main power is not turned off.
The following phenomena are not malfunctions
The cabinet clicks. • The clicking is a creaking sound produced when the cabinet
expands or contracts due to changes in the temperature. This will
not affect the picture or sound.
Unevenness in color • If the brightness is set too high, such unevenness in color may
sometimes develops occur depending upon the nature of the picture. The proper color
in part of the screen. can be restored by reducing the contrast.
OTHER INFORMATIONS
System
Area Country or Region
Color Sound
Bahrain, Kuwait, Israel, Oman, Qatar, United Arab
Emirates, Yemen, and other middle Eastern countries. PAL B/G
Indonesia, Malaysia, Singapore, Thailand, and other
Southeast Asian Countries.
Asia
China PAL D/K
M. E.
China Hong Kong PAL I
Iraq, Islamic Republic of Iran, Lebanon, Saudi Arabia SECAM B/G
Russian Federation SECAM D/K
Myanmar NTSC M
Oceania Australia, New Zealand PAL B/G
Africa Republic of South Africa PAL I
Argentina, Paraguay, Uruguay PAL N
South
Brazil PAL M
America
Chile, Colombia NTSC M
MODEL 15LZR17 / 15LZR28 / 15LZJ28 / 15LZU28X
Rated voltage 15LZJ28:
~ 110 V–240 V, 50/60Hz
15LZR17 / 15LZR28:
~ 220 V–240 V, 50Hz
15LZU28X:
~ 220 V, 50Hz
Power consumption
67W
(at ~ 220 V, 50 Hz)
Dimensions
457.5(W) x 393.0(D) x 352.5(H) mm
(Width x Depth x Height)
Mass 12.1 kg
Picture tube Type 15 Flat square picture tube
(393.4mm) Overall picture tube measured diagonally
(355.6mm) Viewable picture tube measured diagonally
90° deflection
Television Channel System Channel VHF UHF CATV
system coverage
PAL B/G CCIR 2 – 12 21 – 69 X ~ Z+2, S1 ~ S41
(Antenna
PAL I UK — 21 – 69 —
input)
PAL D/K CHINA 1 – 12 13 – 57 Z–1 ~ Z–38
SECAM B/G CCIR 2 – 12 21 – 69 X ~ Z+2, S1 ~ S41
SECAM D/K OIRT 1 – 12 21 – 69 X1 ~ X19
NTSC M US 2 – 13 14 – 69 A–6 ~ A–1, A ~ W, AA ~ ZZ, AAA, BBB
NTSC M JAPAN 1 – 12 13 – 62 M1 ~ M10, S1 ~ S41
Special RF Color system Sound system
signal NTSC4.43 5.5/6.0/6.5 MHz
PAL 60Hz 5.5/6.0/6.5 MHz
Color system PAL/SECAM/NTSC4.43/NTSC3.58
Sound output 2.5 W X 2
Speaker 4 X 11cm (2)
Terminal For 15LZR17
Input [a(1), front and back]: Video, Audio (monaural)
Output [
>(MONITOR)]: Video, Audio (monaural)
For 15LZJ28 / 15LZR28 / 15LZU28X
Input [a(1), front and back]: Video, Audio L, Audio R
Output [
>(MONITOR)]: Video, Audio L, Audio R
Headphone output: Ø3.5 mm (mini jack)
Accessories • Remote control (1) • Rod antenna (1)*
• Batteries (R03, AAA) (2) * 15LZJ28 only
• This Owner's Manual
Design and specifications are subject to change without notice.
Help to recycle, this product indicates material names on main plastic parts.
For 15LZJ28 / 15LZR28 / 15LZU28X models
For 15LZR17 model
Video camera
R
W
Y
R
W
Y
Video camera
W
Y
W
Y
Front
To
video/
audio
outputs
To
video/
audio
outputs
Front
VIDEO
VIDEO
VTR (type without built-in tuner)
VTR etc.
PLAY BACK
REC
YWR
Y
W
R
: Signal flow
: yellow (Video)
: white (Audio L/MONO)
: red (Audio R)
R
W
Y
Y
W
R
Y
W
R
To video
output
To audio
outputs
Back
To video
input
To audio
inputs
(MONITOR)
(1)
VIDEO
AUDIO
VIDEO
AUDIO
VTR (type without built-in tuner)
VTR etc.
PLAY BACK
REC
Y
W
W
Y
Y
W
Y
W
To video
output
To audio
output
To video
input
To audio
input
Back
Y
W
: Signal flow
: yellow (Video)
: white (Audio)
(MONITOR)
(1)
or
+
or
+
AUDIO
L/MONO
R
AUDIO
L/MONO
R
• The illustrations in this manual are of 15 LZJ28 model, if otherwise , it will be stated.
En01_01[15LZR17/28/JU28X]-8 21/6/06, 2:59 PM1