Filter
Top Products
User's Manual
48
CHAPTER 5
Zone 2 Operation
If you have a pair of speakers in a
second room or area (Zone 2), they
can play a stereo source independent
of whatever is playing in the Home
Theater room (Main Zone). You can
also play the same source as selected
in the Main Zone.
The Zone 2 speakers can be pow-
ered by two of the TGR-401's internal
ampli¿ ers, if you enable "Powered Z2"
in the Binding Posts menu. The ampli-
¿ ers that power the surround-back
speakers are switched to play the
Zone 2 speakers instead. An external
power ampli¿ er can be used to power
the Zone 2 speakers.
Zone 2 plays stereo sources, and is
unaffected by the DSP, Sonic Hologra-
phy, surround modes or bass man-
agement.
Audio Connections
The connections for Zone 2 are
shown on page 23.
Note: Zone 2 can play analog
sources independent of what is play-
ing in the Main Zone. It cannot play
from a digital-only source unless that
input is selected and playing in the
Main Zone. To play a source such as
a DVD player in Zone 2 independent
of the Main Zone, make sure you
connect the player's L-R analog audio
output to the TGR-401.
Video Connections
Zone 2 has a composite video
output that can connect to a video
monitor in your other room. This will
only play if the selected source also
has composite video.
Indicators
The front panel has
a green LED to show
the Zone 2 status.
This LED is always on
when Zone 2 is on. If
it is off, there will be
no output to Zone 2.
Turning on Zone 2
With the remote set to operate the
TGR-401, press the ZONE 2 button.
The remote's POWER, VOLUME and
MUTE buttons then work for Zone 2.
Note: Zone 2 can also be turned
on and adjusted without using the
remote. Press the Zone 2 button on
the TGR-401 front panel followed by
Power to turn it on (or off), or adjust
the input source or volume. After 8
seconds of inactivity, the front panel
will revert back to control of the Main
Zone.
Zone 2 operations will work even if
the Main Zone is off.
SETUP CHOICES
INPUTS
SPEAKERS
VIDEO
MAIN ZONE
ZONE 2
CONTROL
DIGITAL OUT DNMX/THRU
DIMMER LOW/MED/HI
MAIN MENU
TRIMS
TONE CONTROLS
MODES
PRESETS
SETUP
SPEAKERS
AUTO SETUP
SPEAKER SIZE
DISTANCE
LEVEL CALIBRATION
EQ
BINDING POSTS
BINDING POSTS CHOICES
AMP SECTION ON ON, OFF
FRONT ON ON, OFF
SURROUND ON ON, OFF
CFG POST OFF OFF, FRONT, SURR
POWERED Z2 OFF ON/OFF
ZONE 2 CHOICES
FIXED VOLUME NONE NONE, 0.0 - 100.0
PWR UP MAX VOL 100.0 0.0 - 100.0
PWR UP MIN VOL 0.0 0.0-100.0 MUST BE LESS THAN POWER UP MAX VOLUME
MAX VOLUME 100.0 0.0-100.0 MUST BE MORE THAN POWER UP MAX VOLUME
PWR UP SOURCE LAST LAST, INPUT 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12
BASS 0 +14 TO -14, 2 DB STEPS
TREBLE 0 +14 TO -14, 2 DB STEPS
BALANCE 0 -20 TO +20, 1 DB STEPS
Zone 2 OSD menu
The ZONE 2 menu allows you to
customize Zone 2 to suit:
FIXED: Set the Zone 2 volume at this
¿ xed level.
PWR UP MAX VOL: Set the Zone 2
turn-on volume so it will not come
on higher than this.
PWR UP MIN VOL: Set the Zone 2
turn-on volume so it will not come
on lower than this level.
MAX VOLUME: Set the Zone 2 vol-
ume so it cannot be higher than
this level.
BASS: Adjust the bass with up to 14
dB of boost or cut.
TREBLE: Adjust the treble with up to
14 dB of boost or cut.
BALANCE: Adjust the balance with up
to 20 dB or adjustment either side.
Binding Posts menu
POWERED Z2: Set to ON for the
Zone 2 binding posts to supply
speaker-level power to your Zone
2 speakers