Filter
Top Products
1-13
MVE-9000 IM
D602 (A-2) : PLL LOCK status LED
REF IN signal format status indication.
Lit when the REF IN signal matches with the switcher
format setup.
D701 (A-2) : SBUS RX status LED
S-BUS receive status indication.
Lit while the data receive is in progress.
D704 (A-2) : SBUS TX status LED
S-BUS send status indication.
Lit while the data send is in progress.
D901 (A-4), D902, D903, D904 (A-5) : COM CPU-1
status LED
COM CPU-1 status indication.
D1001 (A-2) : COM1 100 status LED
COM CPU-1 Ethernet communication speed status
indication.
Lit : 100 Mb/s
Not lit : 10 Mb/s
D1002 (A-2) : COM1 ACT status LED
COM CPU-1 Ethernet communication status indication.
Lit while data send or receive is in progress.
D1101, D1102, D1103, D1104 (A-5) : COM CPU-2
status LED
COM CPU-2 status indication.
D1201 (A-2) : COM2 ACT status LED
COM CPU-2 Ethernet communication status indication.
Lit while data send or receive is in progress.
D1202 (A-2) : COM2 100 status LED
COM CPU-2 Ethernet communication speed status
indication.
Lit : 100 Mb/s
Not lit : 10 Mb/s
D1303 (A-2) :
++
++
+5 V
+5 V power supply status indication.
Lit when the +5 V power is supplied.
ND901, ND902 (A-4) : COM CPU-1 status LED
COM CPU-1 status indication.
ND1101, ND1102 (A-4) : COM CPU-2 status LED
COM CPU-2 status indication.
<Switch>
S101 (A-3) : Mode setting switch for the main CPU
Sets the modes of the main CPU.
Default setting when shipped from the factory is all OFF.
S102 (A-2) : Group ID setting switch for LAN
Sets the group ID for connecting LAN.
For details, refer to “MVS-8000 System Setup Manual”.
S103 (A-2) : Unit ID setting switch for LAN
Sets the unit ID for connecting LAN.
For details, refer to “MVS-8000 System Setup Manual”.
S104 (A-4) : Monitor reset switch for the main
CPU
Pressing this switch resets the system while maintaining
this unit through the main CPU control terminal connector.
S401 (A-1) : System reset switch
Pressing this switch activates the system reset and the
system re-starts.
S402 (A-1) : CA-CPU reset switch
Pressing this switch resets the CA-54CFA board.
S403 (B-1) : Switch setting the number of the
power supply units
Setting switch for the number of the power supply units
that is required for this unit.
Do not change the settings.
By the default setting when shipped from the factory, the
bit 1 and 2 are set to ON and the bit 3 and 4 are set to OFF.
S901 (A-4) : Monitor reset switch for the COM CPU-1
Pressing this switch resets the system while maintaining
this unit through the COM CPU-1 control terminal.
S902 (A-4) : Modes setting switch for the COM CPU-1
Sets the modes of the COM CPU-1.
Default setting when shipped from the factory is all OFF.
S1101 (A-4) : Monitor reset switch for the COM CPU-2
Pressing this switch resets the system while maintaining
this unit through the COM CPU-2 control terminal.
S1102 (A-4) : Modes setting switch for the COM
CPU-2
Sets the modes of the COM CPU-2.
Default setting when shipped from the factory is all OFF.