Filter
Top Products
Additional Information
71
GB
Specifications
AUDIO POWER SPECIFICATIONS:
(MHC-GX90D USA model only)
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
with 6 ohm loads both channels driven, from
120 – 10,000 Hz; rates 40 watts per channel
minimum RMS power, with no more than 10%
total harmonic distortion from 250 milliwatts to
rated output.
Amplifier section
North American model:
MHC-GX90D
Continuous RMS power output (reference)
Front speaker: 60 + 60 watts
(6 ohms at 1 kHz, 10%
THD)
Center speaker: 45 watts (8 ohms at 1 kHz,
10% THD)
Rear speaker: 40 + 40 watts
(6 ohms at 1 kHz, 10%
THD)
Sub woofer: 55 watts (4 ohms at 1 kHz,
10% THD)
Total harmonic distortion less than 0.07%
(6 ohms at 1 kHz,
70 watts)
European model:
MHC-RV800D
DIN power output
Front speaker: 45 + 45 watts
(6 ohms at 1 kHz, DIN)
Center speaker: 33 watts
(8 ohms at 1 kHz, DIN)
Rear speaker: 30 watts
(6 ohms at 1 kHz, DIN)
Sub woofer: 38 watts
(4 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
Front speaker: 60 + 60 watts
(6 ohms at 1 kHz, 10%
THD)
Center speaker: 45 watts (8 ohms at 1 kHz,
10% THD)
Rear speaker: 40 + 40 watts
(6 ohms at 1 kHz, 10%
THD)
Sub woofer: 55 watts
(4 ohms at 1 kHz, 10%
THD)
Music power output (reference)
Front speaker: 120 + 120 watts
(6 ohms at 1 kHz, 10%
THD)
Center speaker: 90 watts (8 ohms at 1 kHz,
10% THD)
Rear speaker: 80 + 80 watts
(6 ohms at 1 kHz, 10%
THD)
Sub woofer: 110 watts
(4 ohms at 1 kHz, 10%
THD)
Other models:
MHC-RV900D
The following measured at AC 120, 127, 220, 240 V,
50/60 Hz
Continuous RMS power output (reference)
Front speaker: 100 + 100 watts (6 ohms
at 1 kHz, 10% THD)
Center speaker: 40 watts (8 ohms at 1 kHz,
10% THD)
Rear speaker: 40 + 40 watts
(6 ohms at 1 kHz, 10%
THD)
MHC-RV600D
The following measured at AC 120, 127, 220, 240 V,
50/60 Hz
DIN power output (rated) 100 + 100 watts (6 ohms
at 1 kHz, DIN)
Continuous RMS power output (reference)
100 + 100 watts (6 ohms
at 1 kHz, 10% THD)
Inputs
MD/VIDEO (AUDIO) IN (phono jacks):
voltage 450/250 mV,
impedance 47 kilohms
GAME (AUDIO) IN (phono jack):
voltage 250 mV,
impedance 47 kilohms
MIC (phone jack) (except for North American and
European models): sensitivity 1 mV,
impedance 10 kilohms
Outputs
MD/VIDEO (AUDIO) OUT (phono jacks):
voltage 250 mV,
impedance 1 kilohm
VIDEO OUT (phono jack):
max. output level
1 Vp-p, unbalanced, Sync
negative, load impedance
75 ohms
S-VIDEO OUT (4-pin/mini-DIN jack):
Y: 1 Vp-p, unbalanced,
Sync negative,
C: 0.286 Vp-p,
load impedance 75 ohms
continued