Sony DRN-XM01H Stereo Receiver User Manual


 
POWER ANT
DC OUT AUDIO
For DRN-XM01C/XM01CK
Connecting the Unit to the
Cigarette Lighter Socket
When the electric power is supplied to the car battery cord, the power
lamp lights up.
Notes
•Route the cords so that they will not interfere with your driving.
•Take care not to accidentally insert a portion of the car connecting pack
cord into the cassette insertion slot. This may cause the cord to break or
damage the car cassette deck.
•To disconnect the cord from your audio equipment, pull it out by
grasping the plug. Never pull it by the cord.
•If the inside of the cigarette lighter socket is dirty with cigarette ash, the
cigarette lighter plug may be heated due to abnormal contact. Be sure
to clean the inside of the cigarette lighter socket before inserting the
plug.
•After using the receiver, eject the car connecting pack from the car
cassette deck and disconnect the car battery cord from the receiver and
the cigarette lighter socket.
•Do not use the receiver when the car’s engine is not running.
Using the Car Connecting Pack
1 Turn down the volume of the car cassette deck.
2 Set the tape selector to the normal (TYPE I) position, and the
DOLBY NR, REPEAT, or BLANK SKIP switch to the OFF
position if such are equipped.
3 Insert the car connecting pack into the cassette deck.
4 Start playback on the car cassette deck.
5 Adjust the volume.
If no sound is heard or the car connecting pack is removed, change the
playback direction on the car cassette deck.
To Remove the Car Connecting Pack
Press the Z (eject) button of the car cassette deck.
Note
You cannot use this car connecting pack with certain car cassette decks.
Fuse Replacement
1 Pull the cigarette lighter plug out of the cigarette lighter
socket.
2 Detach the end of the plug by turning it counterclockwise.
3 Replace the fuse with a new one.
4 Reattach the end of the plug by turning it clockwise firmly.
Notes
•When replacing the fuse, be sure to use one with the correct amperage,
as stated on the fuse case. (1 A, 125 V, 20 mm)
•Do not use a piece of wire instead of a fuse.
•If the replaced fuse opens again, consult your dealer.
For DRN-XM01R
Using the Unit on House Current
Use the AC power adaptor and the audio cord supplied with
DRN-XM01H/XM01HK.
Attaching the Home Stand
Connecting the Unit
Note on the DC plug of the AC power adaptor
This AC power adaptor uses a unified polarity type plug (JEITA
standard). Damage will occur if it is connected to a DC power input jack
without the ! polarity symbol or with another symbol. If the jack of
your audio equipment does not match the AC power adaptor, consult
your dealer.
Symbol of unified polarity type jack
Placement of the Home Antenna
The satellite is located in the south sky. Place the antenna as follows for
proper reception:
– Outside the house
– Place the antenna in an area where there are no obstacles within 20 - 60
degrees facing the southern sky.
– On a flat surface so that it is parallel to the ground.
When you place it indoors, or if there is a building or tree in the direction
of the satellite, the antenna may not be able to receive the radio wave.
Depending on where you live, you may be able to receive radio waves
that are retransmitted by ground repeaters.
Connecting the Unit to your Car with a RF Modulator
Connect it as follows when a diversity
antenna is used for the car audio.
TOYOTA
Connect to the bigger antenna connector.
NISSAN
The optional antenna converter cord XA-82 is
required. The shape of the antenna terminal
is different depending on the model of the
car.
Others
The optional antenna converter cord may be
required. Check with the retailer.
Fuse Replacement
If the fuse blows, check the power connection and replace the fuse. If the
fuse blows again after replacement, there may be an internal malfunction.
Warning
Use a fuse with the specified amperage rating. Use of a higher amperage
fuse may cause serious damage.
Setting the POWER SELECT Switch
This RF modulator supplies power to the receiver and detects the on/off
state by monitoring the load of the power. When the receiver is turned on,
the RF modulator automatically cuts off the antenna line and directly
outputs the sound of the receiver to the car audio with the selected FM
frequency. This prevents the sound from disturbing the FM broadcast
signal. When the receiver is turned off, the antenna line is connected to
the car audio. Besides, you can set the RF modulator to always cut off the
antenna line and output the XM radio sound to the car audio, in this case,
you cannot hear the normal FM broadcast.
POWER
SEL
ON 2 1
1 : Normal use (detecting more than 100 mA load)
2 : Not used (detecting more than 50 mA load)
ON: Not used (cutting off the antenna line)
Changing the Transmitting
Frequency
This unit changes the signal of the XM satellite radio broadcast into an
FM frequency and outputs the sound through an FM tuner. There may be
interference noise while playing the receiver, when the frequency selected
for the receiver is used for transmitting the actual FM broadcast. In such a
case, change the transmitting frequency on the unit. The factory-set is 87.9
MHz.
F.SEL
1234
87.7 MHz
1234
88.1 MHz
1234
88.3 MHz
1234
88.5 MHz
1234
88.7 MHz
1234
88.9 MHz
1234
(Default)
87.9 MHz
Note
When you change the frequency on the unit, be sure to tune your FM
tuner to the newly selected one.
For DRN-XM01H/XM01HK
Car cassette deck
to a cassette
insertion slot
Car
connecting
pack
to a cigarette lighter socket
Power lamp
Car battery cord
to the DC IN 6V
jack
to the
LINE OUT
jack
Fuse (1 A)
Cigarette lighter plug End of the plug
to tighten
to remove
Speaker
system
to a metal point
on the car
to the car
antenna
Car audio
Black
Antenna connecter
to the +12 V power
terminal which is
powered when the
ignition key switch is
in the accessory
position
Be sure to connect
the black earth lead
to it first.
RF Modulator
Power connecting cord
(Supplied)
Fuse (1 A)
Red
POWER SEL (select)
switch
Frequency select switch
For the DRN-XM01C/XM01CK/XM01R
When the Installation and
Connections Have Been Made
Securing the Cord
After installing and connecting the unit, run cord so as not to interfere
with the operation of the vehicle.
Run and fix the cord on the passenger side of the center console with the
supplied cord clamp.
* Clean the mounting surface before installing the cord clamp.
Leave the installed cord clamp for 24 hours before installing the
cord. Otherwise, the cord clamp may come off because of weak
attachment.
Note
Make sure the cord does not get caught in the sliding rails under the front
seats or the front doorsills as this may cause the cord to be severed.
Cord clamp*
to an AC outlet
to the DC IN 6V jack
Cradle
to the DC IN 6V jack
to the LINE OUT jack
Cradle
to the input jacks
of the audio
equipment
Audio cord
to the LINE
OUT jack
AC power adaptor
Precautions
•Do not install the unit where:
– the ambient temperature exceeds 55°C (131°F).
– it will be exposed to direct sunlight or hot air from a heater.
– it will be exposed to rain, water, or high humidity.
– it will be exposed to a lot of dust.
– it will be subject to excessive vibration.
– hinder normal driving activities.
– jeopardize the passengers.
•Be sure to turn off the power of each component before making the
connections.
For DRN-XM01C/XM01CK Customers
Be sure to check that the voltage of the equipment connected to this unit
is correct. Incorrect voltage may cause the equipment to malfunction.
•This unit is designed for negative ground 12 or 24 V DC operation only.
•Avoid high temperatures, such as direct sunlight or hot air from the
heater.
•You cannot use this unit with some car cassette deck.
•Used with some car cassette decks, the car connecting pack may rattle.
This is not a malfunction of the car connecting pack.
Note on the DC plug of the car battery cord
This car battery cord uses a unified polarity type
plug (JEITA standard). Damage will occur if it is
connected to a DC power input jack without the
! polarity symbol or with another symbol.
For DRN-XM01R Customers
•This unit is designed for negative ground 12 V DC operation only.
•Before making connections, disconnect the earth terminal of the car
battery to avoid short circuits.
•Connect the red power input leads only after all other leads have been
connected.
Be sure to connect the red power input lead to the positive 12 V
power terminal which is powered when the ignition switch is in the
accessory position.
Run all earth wires to a common earth point.
For DRN-XM01H/XM01HK Customers
On installing the AC power adaptor
Do not place the AC power adaptor in a location where it is subject to:
– extreme high temperature (E.g., in a car with its windows closed)
– direct sunlight or near a heat source
– mechanical vibration or shock
– a magnetic field (E.g., near a magnet, speaker, or TV)
– excessive dust.
On operating the AC power adaptor
•Make sure the current and voltage of the equipment matches that of the
outlet.
•For safety, if the input current is too high, the unit will automatically
shut down.
•Do not use the unit near a TV set. If you place equipment too close to
the unit while they are being used, you may experience some
interference.
•To prevent damage, be careful not to drop or otherwise cause a
mechanical shock to the unit.
•After using, disconnect the unit from the wall outlet and the equipment.
•Disconnect the unit from the AC outlet by pulling on the plug. Do not
pull on the cord.
•To avoid short-circuiting, do not allow the terminals of the unit or
connector to touch any metal object.
•Use only the recommended AC power adaptor.
For all Customers
On cleaning
•Clean the unit with a soft, dry cloth. If the unit is very dirty, wipe it off
with a soft cloth lightly moistened with a mild detergent solution, and
then wipe with a soft dry cloth.
•Do not use any type of solvent such as alcohol, thinner, or benzine as it
may damage the finish of the cabinet.
•If you use any chemical cleaner, observe the instructions provided with
the product.
•If the cabinet of the unit is splashed with any type of solvent such as
insecticide, or remains in contact for a long time with rubber or vinyl,
the finish or the cabinet may be damaged.
XM antenna
to the ANT
SAT jack
to the ANT
TER jack
SAT
TER
SAT
to the ANT SAT jack
TER
to the ANT TER jack
Tighten the screw at the
bottom of the home stand
to secure the cradle.
To the stand
receptacle at
the bottom of
the cradle
XM antenna
XM antenna
SAT TER
to the ANT
SAT jack
to the ANT
TER jack
Replacing the Lithium Battery
into the Remote Commander
Replace the battery when the buttons on the remote commander do not
work. Remove the old battery and insert a new one.
1
2
3
1 Insert a long and thin object into the hole, then pull out the
lithium battery holder.
2 Place the lithium battery with the positive (+) side facing up.
3 Insert the battery holder into the remote commander until it
clicks.
Battery life (Approx.)
Sony lithium battery CR2025 1 year
Notes on lithium battery
•Keep the lithium battery out of reach of children. Should the battery be
swallowed, immediately consult a doctor.
•Wipe the battery with a dry cloth to assure good contact.
•Be sure to install the battery in the correct polarity position.
•Do not hold the battery with metallic tweezers, as doing so may cause a
short-circuit.
•Do not break up the battery or throw it into a fire, which might cause it
to explode.
Carefully dispose of the used battery.
Note
When the unit is not to be used for a long period of time, remove the
battery to avoid damage from battery leakage and corrosion.
Specifications
Accessories supplied
XM antenna (1)
Remote commander (1)
For DRN-XM01C/XM01CK/XM01R:
Car cradle (1)
Car stand (1)
Screw (5)
Cover (1)
Water proof cushion (1)
Cable guide (3)
Cord clamp (4)
Cushion with the double-sided adhesive tape (1)
Seal (1)
For DRN-XM01C/XM01CK only:
Car battery cord (1)
Car connecting pack (1)
For DRN-XM01R only:
RF modulator (1)
For DRN-XM01H/XM01HK:
Home cradle (1)
Home stand (1)
Audio cord (1)
AC power adaptor (1)
Optional accessories
AC power adaptor AC-E60A
Car battery cord DCC-E260
Car connecting pack CPA-9C