Sony CMTSBT100 Speaker System User Manual


  Open as PDF
of 2
 
CMT-SBT100 (GB) 4-464-273-11 (1)
WARNING
To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or moisture.
To reduce the risk of fire, do not cover the
ventilation opening of the appliance with
newspapers, tablecloths, curtains, etc.
Do not expose the appliance to naked flame
sources (for example, lighted candles).
To reduce the risk of fire or electric shock, do not
expose this appliance to dripping or splashing,
and do not place objects filled with liquids, such
as vases, on the appliance.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
As the main plug is used to disconnect the unit
from the mains, connect the unit to an easily
accessible AC outlet. Should you notice an
abnormality in the unit, disconnect the main plug
from the AC outlet immediately.
This symbol is intended to alert
the user to the presence of
uninsulated“dangerous voltage”
within the product’s enclosure that
may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
Do not expose batteries or appliances with
battery-installed to excessive heat, such as
sunshine and fire.
The unit is not disconnected from the mains as
long as it is connected to the AC outlet, even if the
unit itself has been turned off.
CAUTION
The use of optical instruments with this product
will increase eye hazard.
Owner’s Record
The model and serial numbers are located
on the rear exterior of the unit. Record these
numbers in the space provided below. Refer to
them whenever you call upon your Sony dealer
regarding this product.
Model No.
Serial No.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong.
The wide blade or the third prong are provided
for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
11) Only use attachments/accessories specified by
the manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus.
When a cart is used, use caution whenmoving
the cart/apparatus combination to avoid injury
from tip-over.
13) Unplug this apparatus during lightning storms
or when unused for long periods of time.
14) Refer all servicing to qualified service
personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-
supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
The following FCC statement applies only
to the version of this model manufactured
for sale in the U.S.A. Other versions may
not comply with FCC technical regulations.
NOTE:
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuantto Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
This equipment must not be co-located or
operated in conjunction with any other antenna
or transmitter.
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency
(RF) Exposure Guidelines in Supplement C to
OET65. This equipment has very low levels of
RF energy that it deemed to comply without
maximum permissive exposure evaluation (MPE).
But it is desirable that it should be installed and
operated keeping the radiator at least 20cm
or more away from person’s body (excluding
extremities: hands, wrists, feet and ankles).
Getting Started
red
Rear of the speaker
Remote
Operations
Playing a CD-DA/MP3 disc
1 Press CD FUNCTION on the remote or press
FUNCTION on the unit repeatedly until “CD”
appears in the display .
2 Press the (open/close) button to open
the disc tray .
Load a disc with the label side facing up.
Label side
(printed side)
(open/close)
Press the (open/close) button to close
the disc tray .
Press (play/pause) button .
Playback starts.
Notes
ˎIf you cannot remove the disc and “LOCKED” appears in the
display , contact your nearest Sony dealer.
ˎDo not load a disc with non-standard shapes (e.g., heart,
square, star). Doing this may cause irreparable damage to
the system.
ˎDo not use a disc with tape, stickers or paste on it as this
may cause malfunction.
ˎWhen you remove a disc, do not touch the surface of the
disc.
Other operations
To Do the following:
Pause playback
Press
. To resume play,
press the button again.
Stop playback
Press
.
Select a track
or file
Press /
.
Find a point in a
track or file
Hold down /
(or
/
on the unit)
during playback, and release
the button at the desired point.
Select Repeat
Play
Press REPEAT
repeatedly
until “
” (all tracks of files)
or “
1” (single track or file)
appears.
Select a folder on
an MP3 disc
Press
+/
repeatedly.
Remove a disc
Press
on the unit.
To change the play mode
Press PLAY MODE repeatedly while the player
is stopped. You can select Normal Play mode (no
indication or “FLDR”* appears), Shuffle Play mode
(“SHUF” or “FLDR SHUF”* appears), or Program
Play mode (“PGM” appears).
Play mode
* When “FLDR” or “FLDR SHUF” appears, all the files in the
selected folder on the MP3 disc will be played. When
playing a CD-DA disc, the system performs the same
operation as Normal Play (no indication) or Shuffle Play
“SHUF.”
When “PUSH STOP” appears
You cannot change the play mode during
playback. Stop playback then change the play
mode.
Note on the play mode
If the power cord is disconnected when the
system is on, the play mode returns to Normal
Play.
Notes on Repeat Play
ˎ“ ” indicates that all tracks or files will be repeated until
you stop playback.
ˎ“
1” indicates that a single track or file will be repeated
until you stop playback.
ˎIf the power cord is disconnected when the system is on,
Repeat Play is cancelled.
Notes on Shuffle Play mode
ˎWhen Shuffle Play mode is set to “SHUF,” the system
shuffle-plays all tracks or files on the disc. When Shuffle
Play mode is set to “FLDR SHUF,” the system shuffle-plays all
tracks or files in selected folder.
ˎWhen you turn off the system, the selected Shuffle Play
mode (“SHUF” or “FLDR SHUF”) is cleared and the play
mode returns to Normal or FLDR Play mode.
Notes on playing MP3 discs
ˎDo not save unnecessary folders or files on a disc that has
MP3 files.
ˎFolders that have no MP3 files are not recognized on the
system.
ˎThe system can only play MP3 files that have a file
extension of “.mp3.”
ˎEven when file name has the “.mp3” file extension, if it is
not an audio MP3 file, playing this file may generate a loud
noise, which could cause damage of the system.
ˎThe maximum number of MP3 folders and files compatible
with this system is:
999* folders (including the root folder)
999 files
250 files in a single folder
8 folder levels (in the tree structure of files)
ˎCompatibility with all MP3 encoding/writing software,
CD-R/RW drive and recording device, and recording media
cannot be guaranteed. Incompatible MP3 discs may
produce noise or interrupted audio or may not play at all.
*
This include f
olders that have no MP3 or other files. The
number of folders that the system can recognize may
be less than actual number of folders, depending on the
folder structure.
Creating your own program
(Program Play)
1 Press CD FUNCTION
on the remote or press
FUNCTION
on the unit repeatedly until “CD”
appears in the display .
2 Press PLAY MODE
repeatedly until “PGM”
appears while the player is stopped.
3 Select a folder (MP3 disc only).
Press
+/
repeatedly to select the
desired folder.
If you want to program all files in the folder,
press
.
4 Select the desired track or file number.
Press /
repeatedly until the desired
track or file number appears.
Total playing time
of the selected
track or file
Selected track
or file number
5 Press
.
“--.--” appears when the total playing time
exceeds 100 minutes for an CD-DA or when you
program an MP3 files.
6 Repeat steps 3 through 5 to program
additional tracks or files, up to a total of 25
tracks or files.
7 Press
.
Your program of tracks or files starts playback.
The programmed files or tracks remain
available until you remove the disc from the
disc tray
or unplug the power cord.
To play the same program again, press
.
To cancel Program Play
Press PLAY MODE repeatedly until “PGM”
disappears while the player is stopped.
To delete the last track or file of the
program
Press CLEAR
while the player is stopped.
Notes
ˎIf the disc is ejected after programming, all the
programmed tracks or files are deleted.
ˎIf the power cord is disconnected when the system is on,
the programmed tracks or files are deleted.
Listening to the radio
Tuning in a radio station
1 Press TUNER FUNCTION
on the remote or
press FUNCTION
on the unit repeatedly
until “TUNER FM” or “TUNER AM” appears in
the display.
2 Perform tuning.
For automatic scanning
Press TUNING MODE
repeatedly until “AUTO”
appears, and then press TUNE +/
. Scanning
stops automatically when a station is tuned in,
and “STEREO” (for stereo programs only) appears
in the display .
If the scanning does not stop, press
to stop
scanning, then perform manual tuning (below).
When you tune in a station that provides RDS
services, information such as the service name or
station name is provided by broadcasts.
For manual tuning
Press TUNING MODE
repeatedly until
“MANUAL” appears, and then press TUNE +/
repeatedly to tune in the desired station.
Tip
To reduce static noise on a weak FM stereo station, press FM
MODE repeatedly until “MONO” appears to turn off stereo
reception.
To change the AM tuning interval
The default setting for AM tuning interval is 9 kHz
(or 10 kHz for some areas). Use the buttons on the
unit to perform this operation.
1 Press FUNCTION
on the unit repeatedly to
select the AM station.
2 Press
/
to turn off the system.
3 Press and hold FUNCTION
and press
/
on the unit.
“STEP 9K” or “STEP 10K” appears in the display
. When you change the interval, all the AM
preset stations are erased.
Presetting radio stations
1 Tune in the desired station.
Power input (AC IN)
After all equipments are connected, connect the
power cord to the wall outlet.
Speakers (left/right) connectors
Firmly connect the right speaker cord to R, and
the left speaker cord to L.
AUDIO IN (external input) jack
Connect optional external equipment with an
audio connecting cable (not supplied).
Antennas
FM lead antenna (supplied)
AM loop antenna (supplied)
Find a location and an orientation that provide
good reception, and then fix the antennas to a
stable surface (window, wall, etc.).
Keep the antennas away from the unit, power
cord and other AV components to avoid picking
noise.
Secure the end of the FM lead antenna with
adhesive tape.
To prepare the AM loop antenna
Rewind an
antenna cord
wound around the
antenna and raise
the antenna stand.
Stand the
antenna and
secure it to the
slit until it clicks.
This manual mainly explains operations using
the remote, but the same operations can also be
performed using the buttons on the unit having
the same or similar names.
To use the remote
Slide and remove the battery compartment lid,
and insert the two supplied R6 (size AA) batteries,
side first, matching the polarities shown below.
Notes on using the remote
ˎWith normal use, the batteries should last for about 6
months.
ˎDo not mix an old battery with a new one or mix different
types of batteries.
ˎIf you do not use the remote for a long period of time,
remove the batteries to avoid damage from battery leakage
and corrosion.
Location of Controls
Unit (Front)
Tip
When you use headphones, connect to (headphone) jack .
ˎWith some connected USB devices, it may take a long time
to transmit signals from the system or to finish reading the
USB device.
ˎCompatibility with all encoding/writing software cannot be
guaranteed. If audio files on the USB device were originally
encoded with incompatible software, those files may
produce noise or ,may malfunction.
ˎThe maximum number of folders and files on the USB
device compatible with this system is:
1,000* folders (including the root folder)
3,000 files
250 files in a single folder
8 folder levels (in the tree structure of files)
* This includes folders that have no playable audio file and
empty folders. The number of folders that the system
can recognize may be less than actual number of folders,
depending on the folder structure.
ˎThe syst
em does not necessarily support all the functions
provided in a connected USB device.
ˎF
olders that have no audio files are not recognized.
ˎThe audio f
ormats that you can listen to with this system
are as follows:
MP3:
file extension “.mp3”
WMA:
file extension “.wma”
AA
C: file extension “.m4a,” “mp4” or “.3gp”
Note that even when file name has the correct file
extension, if the actual file differs, the system may produce
noise or may malfunction.
Charging a USB device or iPod/
iPhone/iPad
If you connect a USB device or iPod/iPhone/iPad
to the USB port
when the system is turned on,
charging begins automatically.
To stop charging the USB device
Press
/
to turn off the system, and then
disconnect the USB cable.
Notes
ˎYou cannot charge the USB device or iPod/iPhone/iPad
when the system is off. Some USB devices and iPod/iPhone
may not be charged owing to their characteristics.
ˎIf the system enters Standby mode during charging of a
USB device or iPod/iPhone/iPad, the charging stops in
progress. Before charging, turn off the Automatic Standby
function. For details, see “Setting the Automatic Standby
function.”
Using the BLUETOOTH function
You can listen to music from your iPod/iPhone/
iPad or BLUETOOTH device over a wireless
connection.
Before using the BLUETOOTH function, perform
pairing to register your BLUETOOTH device.
The system supports registration and connection
of the BLUETOOTH device and NFC, which enables
data communication by just touching a specified
location. For details on NFC, see “Connecting by
one-touch action (NFC).”
What is pairing?
The BLUETOOTH devices to be connected must be
registered with each other beforehand. Pairing is
an operation of registering two devices.
Once a pairing operation is performed, it does
not have to be performed again. In the following
cases, however, a pairing operation must be
performed again:
ˎP
airing information was erased when the
BLUETOOTH device was repaired.
ˎY
ou attempt to pair the system with more than
10 BLUETOOTH devices.
This system can pair with up to 9 BLUETOOTH
devices. If you pair another BLUETOOTH device
after pairing with 9 devices was performed,
pairing information of the device that was
connected with the system first is overwritten
with that of the new device.
ˎP
airing registration information of this system is
erased from the connected device.
ˎIf you initializ
e the system or erase the
pairing history with the system, all the pairing
information will be erased.
About the BLUETOOTH indicator
The BLUETOOTH indicator in the center of the
BLUETOOTH button
allows checking of the
BLUETOOTH status.
System status Indicator status
The system is in
BLUETOOTH Standby
(when the system is on).
Flashes slowly in blue.
During BLUETOOTH
pairing
Flashes quickly in blue.
The system is
attempting to connect
with a BLUETOOTH
device.
Flashes in blue.
The system has
established in
connection with a
BLUETOOTH device.
Lit in blue.
Enabling reception of AAC codec
You can receive data in AAC codec format from a
BLUETOOTH device. To enable reception, set up
using the option menu.
1 Press OPTIONS
to display the setting menu.
2 Press
/
repeatedly to select “BT AAC,”
then press
.
3 Press
/
repeatedly to select “ON” or
“OFF,” then press
.
ON: to receive in AAC codec format
OFF: to receive in SBC codec format
2 Press TUNER MEMORY
.
Preset number
3 Press TUNE +/
repeatedly to select a
preset number.
If another station is already assigned to the
selected preset number, the station is replaced
by the new station.
4 Press
to register the station.
“COMPLETE” appears in the display .
5 Repeat steps 1 through 4 to register other
stations.
You can preset up to 20 FM, 10 AM stations.
To tune in to a preset radio station
Press TUNING MODE
repeatedly until “PRESET”
appears in the display , and then press TUNE
+/
to select the preset number to which the
desired station is registered.
Playing a file on a USB device
You can play audio files stored on a USB device by
connecting a USB memory or USB device to the
system. The playable audio format is MP3/WMA*/
AAC*.
Check the websites below for the information
about compatible USB devices.
For customers in the United States:
http://esupport.sony.com/
For customers in Canada:
http://esupport.sony.com/CA/
* Files with DRM (Digital Rights Management) copyright
protection or files downloaded from an online music store
cannot be played on this system. If you try to play one of
these files, the system plays the next unprotected audio
file.
1 Press USB FUNCTION
on the remote or
press FUNCTION
on the unit repeatedly
until “USB” appears in the display .
2 Connect the USB device directly or via the USB
cable supplied with the USB device to the USB
port on the unit.
3 Press to start playback.
Other operations
To Do the following:
Pause playback
Press . To resume play,
press the button again.
Stop playback
Press
. To resume play,
press
*1
. To cancel
resume play, press
again
*2
.
Select a folder
Press
+/
repeatedly.
Select a file
Press /
.
Find a point in
a file
Hold down /
(/
on the unit)
during playback, and release
the button at the desired point.
Select Repeat
Play
Press REPEAT
repeatedly
until “
” (all audio files) or
“
1” (single audio file)
appears.
*1
When playing a VBR MP3/WMA file, the system may
resume playback from a different point.
*2
When resume play is canceled, the display returns to the
number of folders.
To change the play mode
Press PLAY MODE repeatedly while the player
is stopped. You can select Normal Play mode (no
indication or “FLDR” appears
*1
), or Shuffle Play
mode (“SHUF” or “FLDR SHUF” appears
*2
).
*1
When no indication is selected, the system plays all files on
the USB device. When “FLDR” is selected, the system plays
all files in the selected folder on the USB device.
*2
When “SHUF” is selected, the system shuffle-plays all audio
files on the USB device. When “FLDR SHUF” is selected, the
system shuffle-plays all audio files in the selected folder.
Note on the play mode
If the power cord is disconnected when the
system is on, the play mode returns to Normal
Play.
Notes on Repeat Play
ˎ“ ” indicates that all files will be repeated until you stop
playback.
ˎ“
1” indicates that a single file will be repeated until you
stop playback.
ˎIf the power cord is disconnected when the system is on,
Repeat Play is cancelled.
Note on Shuffle Play mode
When you turn off the system, the selected Shuffle Play
mode (“SHUF” or “FLDR SHUF”) is cleared and the play mode
returns to Normal Play mode (no indication or “FLDR”).
Notes
ˎThe playback order for the system may differ from the
playback order of the connected digital music player.
ˎBe sure to turn off the system before removing the USB
device. Removing the USB device while the system is turned
on may corrupt the data on the USB device.
ˎWhen USB cable connection is necessary, connect the USB
cable supplied with the USB device to be connected. For
details on connection, refer to the operation manual of the
USB device.
ˎIt may take time before “READING” appears after
connecting, depending on the type of USB device
connected.
ˎDo not connect the USB device through a USB hub.
ˎWhen the USB device is connected, the system reads all the
files on the USB device. If there are many folders or files on
the USB device, it may take a long time to finish reading the
USB device.
Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause undesired
operation of this device.
This equipment complies with IC radiation
exposure limits set forth for an uncontrolled
environment and meets RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment
has very low levels of RF energy that it deemed to
comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it should
be installed and operated keeping the radiator
at least 20cm or more away from person’s body
(excluding extremities:hands, wrists, feet and
ankles).
Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side. However,
since the audio material side does not conform to
the Compact Disc (CD) standard, playback on this
product is not guaranteed.
Music discs encoded with copyright
protection technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware
that among those discs, there are some that do
not conform to the CD standard and may not be
playable by this product.
License and Trademark Notice
ˎWindows Media is either a registered trademark
or trademark of Microsoft Corporation in the
United States and/or other countries.
ˎMPEG Layer-3 audio coding technology and
patents licensed from Fraunhofer IIS and
Thomson.
ˎThe BLUETOOTH® word mark and logos are
registered trademarks owned by BLUETOOTH
SIG, Inc. and any use of such marks by Sony
Corporation is under license. Other trademarks
and trade names are those of their respective
owners.
ˎThe NMark is a trademark or registered
trademark of NFC Forum, Inc. in the United
States and in other countries.
ˎAndroid is a trademark of Google Inc.
ˎThis product is protected by certain intellectual
property rights of Microsoft Corporation. Use or
distribution of such technology outside of this
product is prohibited without a license from
Microsoft or an authorized Microsoft subsidiary.
ˎThe system names and product names indicated
in this manual are generally the trademarks or
registered trademarks of the manufacturer. ™
and ® marks are omitted in this manual.
Notes
ˎIf you initiate setup during BLUETOOTH connection, the
connection is cut.
ˎWhen using an Apple product, update it to the latest
software version. For details on updating, refer to the
operation manual supplied with your Apple product.
ˎIf sound is int
errupted during reception in AAC codec
format, set the BT AAC menu to “OFF.”
Pairing the system with a BLUETOOTH
device
Connection example
BLUETOOTH device
such as a “WALKMAN”
1 Place the BLUETOOTH device to be connected
within 1 meter from the system.
2 Press BLUETOOTH FUNCTION
or press
FUNCTION
on the unit repeatedly until “BT
AUDIO” appears in the display
.
ˎThe BLUETOOTH indicator
flashes slowly
in blue.
ˎIf the system has been automatically
connected with the BLUETOOTH device in
the past, press BLUETOOTH
on the unit
to cancel the connection so that “BT AUDIO”
appears in the display
.
3 Press and hold BLUETOOTH
on the unit for
2 seconds or longer.
The BLUETOOTH indicator
flashes quickly in
blue and “PAIRING” flashes in the display
.
The system is in Pairing mode.
4 Perform the pairing operation on the
BLUETOOTH device and search for this system
with the BLUETOOTH device.
When searching has finished, a list of the
devices found may appear on the BLUETOOTH
device display.
ˎThis system appears as “SONY:CMT-SBT100.”
If it does not appear, perform the procedure
from step 1 again.
ˎWhen est
ablishing connection with this
system, select the audio profile (A2DP, AVRCP)
on the BLUETOOTH device.
ˎIf the BLUETOOTH device does not support
AVRCP (Audio Video Remote Control Profile),
you cannot perform playback or stop
playback with the system.
ˎFor details on operations of the BLUETOOTH
device to be connected, refer to the operation
manual supplied with your BLUETOOTH
device.
5 Select “SONY:CMT-SBT100” in the display of
the BLUETOOTH device.
If prompted to enter a passkey on the
BLUETOOTH device, enter “0000.”
6 Operate the BLUETOOTH device and perform
BLUETOOTH connection.
When pairing is completed and connection
with the BLUETOOTH device is established
correctly, the display
changes to “BT AUDIO”
from “PAIRING” and the BLUETOOTH indicator
flashes slowly in blue.
ˎDepending on the type of BL
UETOOTH device,
connection may start automatically after
pairing is completed.
Notes
ˎ“Passkey” may be called “Passcode,” “PIN code,” “PIN
number” or “Password,” etc., depending on the device.
ˎThe pairing standby status of the system is cancelled after
about 5 minutes. If pairing is not successful, perform the
procedure from step 1.
ˎIf you w
ant to pair with several BLUETOOTH devices,
perform the procedure from step1 to 6 individually for each
BLUETOOTH device.
Tip
You can perform a pairing operation or attempt to make a
BLUETOOTH connection with another BLUETOOTH device
while the BLUETOOTH connection is established with one
BLUETOOTH device. The currently established BLUETOOTH
connection is cancelled when BLUETOOTH connection with
another device is successfully established.
To erase the pairing registration
information
1 Press BLUETOOTH FUNCTION
on the remote
or press FUNCTION
on the unit repeatedly
until “BT AUDIO” appears in the display
.
When the system is connected with a
BLUETOOTH device, the device name set for the
connected BLUETOOTH device appears in the
display
of the system. Press BLUETOOTH
on the unit to cancel the connection with that
BLUETOOTH device then display “BT AUDIO.”
2 Press OPTIONS
to display the setting menu.
3 Press
/
repeatedly to select “DEL LINK,”
then press
.
4 Press
/
repeatedly to select “OK,” then
press
.
“COMPLETE” appears and all the pairing
information is erased.
Note
If you have erased the pairing information, you cannot make
a BLUETOOTH connection unless pairing is performed again.
To connect with a BLUETOOTH device again, you must enter
the passkey on the BLUETOOTH device.
Setting the clock
1 Press 
to turn on the system.
2 Press TIMER MENU
to select the clock set
mode.
If “PLAY SET” flashes, press /
repeatedly
to select “CLOCK,” and then press
(enter)
.
3 Press /
repeatedly to set the hour, then
press
(enter)
.
4 Use the same procedure to set the minutes.
Note
The clock settings are reset when you disconnect the power
cord or if a power failure occurs.
To display the clock when the system is off
Press DISPLAY
repeatedly to display the clock.
The clock is displayed for about 8 seconds.
If the system is in BLUETOOTH Standby mode, the
clock does not appear by pressing DISPLAY .
Attaching speaker pads
Attach the supplied speaker pads to the bottom
of the speakers to prevent slipping.
4-464-273-11 (1)
Home Audio System
GB
Operating Instructions
©2013 Sony Corporation Printed in China
CMT-SBT100