Sony CMT-BX20i Stereo System User Manual


 
CMT-BX20i.GB.3-293-641-11(1)
Other Operations
Creating your own program
(Program Play)
1 Press FUNCTION +/ (or FUNCTION on the unit)
repeatedly to select the CD function.
2 Press PLAY MODE
repeatedly until “PGM” appears
while the player is stopped.
3 Press /
repeatedly until the desired
track or le number appears.
When programming les, press +/
repeatedly
to select the desired folder, and then select the desired
le.
Total playing time of program
(including selected track
or le)
Selected track or le
number
4 Press (or ENTER on the unit)
to add the track
or le to the program.
. ” appears when the total program time
exceeds 100 minutes for a CD, or when you select a
CD track whose number is 21 or over, or when you
select an MP3 le.
5 Repeat steps 3 through 4 to program additional
tracks or les, up to a total of 25 tracks or les.
6 To play your program of tracks or les, press (or
CD  on the unit)
.
e program remains available until you open the disc
tray. To play the same program again, press (or
CD  on the unit)
.
To cancel Program Play
Press PLAY MODE
repeatedly until “PGM”
disappears while the player is stopped.
To delete the last track or le of the program
Press CLEAR
while the player is stopped.
Presetting radio stations
You can preset your favorite radio stations and tune
them in instantly by selecting the corresponding preset
number.
Use buttons on the remote to preset stations.
1 Tune in the desired station (See Listening to the
radio).
2 Press TUNER MEMORY
.
Preset number
3 Press +/
repeatedly to select your desired
preset number.
If another station is already assigned to the selected
preset number, the station is replaced by the new
stations.
4 Press
.
5 Repeat steps 1 through 4 to store other stations.
You can preset up to 20 FM and 10 AM stations. e
preset stations are retained for about half a day even
if you disconnect the power cord or if a power failure
occurs.
6 To call up a preset radio station, press TUNING
MODE
repeatedly until “PRESET” appears, and
then press +/
repeatedly to select the desired
preset number.
Using the Timers
e system oers two timer functions. If you use the Play
Timer with the Sleep Timer, the Sleep Timer has priority.
Use buttons on the remote to use the timer functions.
Sleep Timer:
You can fall asleep to music. is function works even if
the clock is not set.
Press SLEEP
repeatedly. If you select “AUTO,” the
system automatically turns o aer the current disc stops
or in 100 minutes.
Play Timer:
You can wake up to CD, tuner or iPod at a preset time.
Make sure you have set the clock.
1 Prepare the sound source.
Prepare the sound source, and then press VOLUME
+/
to adjust the volume.
To start from a specic track or le, create your own
program.
2 Press TIMER MENU
.
3 Press
/
repeatedly to select “PLAY SET?,” and
then press
.
“ON” appears, and the hour indication ashes.
4 Set the time to start playback.
Press
/
repeatedly to set the hour, and then
press
.
e minute indication ashes. Use the procedure
above to set the minutes.
5 Use the same procedure as in step 4 to set the time
to stop playback.
6 Select the sound source.
Press
/
repeatedly until the desired sound
source appears, and then press
. e display
shows the timer settings.
7 Press 
to turn o the system.
e system turns on 15 seconds before the preset time.
If the system is on at the preset time, the Play Timer
will not play.
To activate or check the timer again
1 Press TIMER MENU
.
“TIMER SEL?” ashes in the display.
2 Press
.
3 Press
/
repeatedly to select “PLAY SEL?,” then
press
.
To cancel the timer
Repeat the same procedure as above until “TIMER
OFF?” appears in step 3, and then press
.
To change the setting
Start over from step 1.
Note on the iPod touch user
e Play Timer may not be activated depending on the status of the
connected iPod touch.
Tip
e Play Timer setting remains as long as the setting is not canceled
manually.
1 Make sure the power cord and speaker cords are
correctly and rmly connected.
2 Find your problem in the checklist below, and take
the indicated corrective action.
If the issue persists, contact your nearest Sony dealer.
If the STANDBY indicator ashes
Immediately unplug the power cord, and check the
following items.
If your system has a voltage selector, is the voltage
selector set to the correct voltage?
Are you using only the supplied speakers?
Is anything blocking the ventilation holes on the top
or back of the system?
Is the iPod connector
short-circuited?
Aer the STANDBY indicator
stops ashing,
reconnect the power cord, and turn on the system. If
the issue persists, contact your nearest Sony dealer.
General
Sound comes from one channel, or the left and
right volumes are unbalanced.
Place the speakers as symmetrically as possible.
Connect only the supplied speakers.
Severe hum or noise.
Move the system away from sources of noise.
Connect the system to a dierent wall socket.
Install a noise lter (available separately) to the power
cord.
The remote does not function.
Remove any obstacles between the remote and the
remote sensor
on the unit, and position the unit
away from uorescent lights.
Point the remote at the system’s sensor.
Move the remote closer to the system.
CD/MP3 player
The sound skips, or the disc will not play.
Wipe the disc clean, and replace it.
Move the system to a location away from vibration (for
example, on top of a stable stand).
Move the speakers away from the system, or place them
on separate stands. At high volume, speaker vibration
may cause the sound to skip.
Play does not start from the rst track.
Press PLAY MODE
repeatedly until both “PGM”
and “SHUF” disappear to return to normal play.
Starting playback takes more time than usual.
e following discs take a longer time to start playback.
a disc recorded with a complicated tree structure.
a disc recorded in multisession mode.
a disc that has not been nalized (a disc to which data
can be added).
a disc that has many folders.
Tuner
Severe hum or noise, or stations cannot be
received. (“TUNED” or “STEREO” ashes on the
display.)
Connect the antenna properly.
Find a location and an orientation that provide good
reception, and then set up the antenna again.
Keep the antenna away from the speaker cords and the
power cord to avoid picking up noise.
Connect a commercially available external antenna.
Consult your nearest Sony dealer if the supplied AM
antenna has come o the plastic stand.
Turn o nearby electrical equipment.
To change the AM tuning interval
e AM tuning interval is factory-preset to 9 kHz (or
10 kHz, for some areas).
Use buttons on the unit to change the AM tuning
interval.
1 Tune in any AM station, and then turn o the
system.
2 While holding down ENTER
, press 
.
All the AM preset stations are erased. To reset the
interval to the factory preset, repeat the procedure.
To improve tuner reception
Turn o CD player power by using the CD power
management function. By default, CD power is turned on.
1 Press FUNCTION +/ (or FUNCTION on the unit)
repeatedly to select the CD function, and then turn
o the system.
2 After “STANDBY” stops ashing, press 
on the
unit while holding down CANCEL
on the unit.
“CD POWER OFF” appears. With CD player power
turned o, disc access time is increased. To turn on
CD player power, repeat the procedure until “CD
POWER ON” appears.
To reset the system to factory settings
If the system still does not operate properly, reset the
system to factory settings.
Use buttons on the unit to reset the unit to its factory
default settings.
1 Disconnect and reconnect the power cord, and then
turn on the system.
2 Press 
, VOL +
and CANCEL
at the
same time.
All user-congured settings, such as preset radio
stations, timer, and the clock, are deleted.
Troubleshooting
iPod
There is no sound.
Make sure the iPod is connected securely.
Make sure the iPod is playing music.
Adjust the volume.
The sound is distorted.
Turn down the volume.
Set the “EQ” setting of the iPod to “O” or “Flat.”
The iPod cannot be charged.
Make sure the iPod is connected securely.
Messages
CD Over: You have reached the end of the disc while
pressing
during playback or pause.
Complete: e preset operation ended normally.
LOCKED: e disc tray does not open. Contact your
nearest Sony dealer.
No Disc: ere is no disc in the system, or you have
loaded a disc that cannot be played.
No Step: All of the programmed tracks or les have been
erased.
Push STOP!: You pressed PLAY MODE
during
playback.
Reading: e system is reading information of the disc.
Some buttons are not available.
Step Full!: You tried to program more than 26 tracks or
les (steps).
TIME NG!: e Play Timer start and end times are set to
the same time.
Precautions
Discs that this system CAN play
Audio CD
CD-R/CD-RW (audio data/MP3 les)
Discs that this system CANNOT play
CD-ROM
CD-R/CD-RW other than those recorded in music CD
format or MP3 format conforming to ISO9660 Level
1/Level 2, Joliet or multisession
CD-R/CD-RW recorded in multisession that have not
ended by “closing the session”
CD-R/CD-RW of poor recording quality, CD-R/CD-
RW that have scratches or are dirty, or CD-R/CD-RW
recorded with an incompatible recording device
CD-R/CD-RW which is nalized incorrectly
Discs containing les other than MPEG 1 Audio Layer-
3 (MP3) les
Discs of non-standard shape (for example, heart,
square, star)
Discs that have adhesive tape, paper, or sticker attached
to them
Rental or used discs with attached seals where the glue
extends beyond the seal
Discs that have labels printed using ink that feels tacky
when touched
Notes on discs
Before playing, wipe the disc with a cleaning cloth from
the center out to the edge.
Do not clean discs with solvents, such as benzine
thinner, or commercially available cleaners or anti-
static spray intended for vinyl LPs.
Do not expose discs to direct sunlight or heat sources
such as hot air ducts, nor leave it in a car parked in
direct sunlight.
Note on DualDiscs
A DualDisc is a two sided disc product which mates
DVD recorded material on one side with digital
audio material on the other side. However, since the
audio material side does not conform to the Compact
Disc (CD) standard, playback on this product is not
guaranteed.
Music discs encoded with copyright protection
technologies
is product is designed to playback discs that conform
to the Compact Disc (CD) standard. Recently, various
music discs encoded with copyright protection
technologies are marketed by some record companies.
Please be aware that among those discs, there are some
that do not conform to the CD standard and may not be
playable by this product.
Copyrights
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
MPEG Layer-3 audio coding technology and patents
licensed from Fraunhofer IIS and omson.
All other trademarks and registered trademarks are of
their respective holders. In this manual,
TM
and ® marks
are not specied.
On safety
Completely disconnect the power cord (mains lead)
from the wall socket (mains) if it is not going to be used
for an extended period of time. When unplugging the
unit, always grip the plug. Never pull the cord itself.
Should any solid object or liquid get into the system,
unplug the system, and have it checked by qualied
personnel before operating it again.
e AC power cord can be changed only by a qualied
service facility.
On placement
Do not place the system in an inclined position or in
locations that are extremely hot, cold, dusty, dirty, or
humid or lacking adequate ventilation, or subject to
vibration, direct sunlight or a bright light.
Be careful when placing the unit or speakers on
surfaces that have been specially treated (for example,
with wax, oil, polish) as staining or discoloration of the
surface may result.
If the system is brought directly from a cold to a warm
location or is placed in a very damp room, moisture
may condense on the lens inside the CD player, and
cause the system to malfunction. In this situation,
remove the disc, and leave the system turned on for
about an hour until the moisture evaporates.
On heat buildup
Heat buildup on the unit during operation is normal
and is not cause for alarm.
Do not touch the cabinet if it has been used
continuously at a high volume because the cabinet may
have become hot.
Do not obstruct the ventilation holes.
On the speaker system
is speaker system is not magnetically shielded, and
the picture on nearby TV sets may become magnetically
distorted. In this situation, turn o the TV, wait 15 to 30
minutes, and turn it back on.
If there is no improvement, move the speakers far away
from the TV.
Cleaning the cabinet
Clean this system with a so cloth slightly moistened
with a mild detergent solution. Do not use any type
of abrasive pad, scouring powder, or solvent, such as
thinner, benzine, or alcohol.
Specications
Main unit
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
(e United States model only)
With 6 ohm loads, both channels driven, from 120 10,000 Hz; rated 25 watts
per channel minimum RMS power, with no more than 10% total harmonic
distortion from 250 milliwatts to rated output.
Amplier section
DIN power output (rated):
18 + 18 W (6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference): 25 + 25 W (6 ohms at 1 kHz,
10% THD)
Inputs
AUDIO IN (stereo mini jack): voltage 250 mV, impedance 47 kilohms
Outputs
PHONES (stereo mini jack): accepts headphones of 8 ohms or more
SPEAKER: accepts impedance of 6 to 16 ohms
CD player section
System: Compact disc and digital audio system
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6µW
* is output is the value measurement at a distance of 200mm from the
objective lens surface on the Optical Pick-up Block with 7mm aperture.
Frequency response: 20 Hz 20 kHz
Signal-to-noise ratio: More than 90 dB
Dynamic range: More than 90 dB
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section:
Tuning range:
North American model: 87.5
108.0 MHz (100 kHz step)
Other models: 87.5
108.0 MHz (50 kHz step)
Antenna: FM lead antenna
Antenna terminals: 75 ohms unbalanced
Intermediate frequency: 10.7 MHz
AM tuner section:
Tuning range:
North American model:
530 1,710 kHz (with 10 kHz tuning interval)
531 1,710 kHz (with 9 kHz tuning interval)
Australian model:
531 1,710 kHz (with 9 kHz tuning interval)
530 1,710 kHz (with 10 kHz tuning interval)
Other models:
531 1,602 kHz (with 9 kHz tuning interval)
530 1,610 kHz (with 10 kHz tuning interval)
Antenna: AM loop antenna, external antenna terminal
Intermediate frequency: 450 kHz
iPod section
Compatible iPod models:
iPod touch
iPod nano 3rd
generation
(video)
iPod classic
iPod nano 2nd
generation
(aluminum)
iPod 5th
generation
(video)
iPod nano 1st
generation
iPod 4th
generation
(color display)
iPod 4th
generation
iPod mini
Speaker
Speaker system: Full-range, bass-reex, 10 cm, cone type
Rated impedance: 6 ohms
Dimensions (w/h/d): Approx. 140 × 245 × 215 mm
Mass: Approx. 1.9 kg net
General
Power requirements:
North American model: 120 V AC, 60 Hz
Australian model: 230
240 V AC, 50/60 Hz
Other models: 120 V, 220 V, 230
240 V AC, 50/60 Hz, adjustable with
voltage selector
Power consumption: 63 watts
Dimensions (w/h/d) (excl. speakers): Approx. 215 × 140 × 298 mm
Mass (excl. speakers): Approx. 3.9 kg
Supplied accessories: Remote Commander (1)/R6 (Size AA) batteries (2)/AM
loop antenna (1)/FM lead antenna (1)/iPod Dock Adaptors (1 set) (Except for
Australian model)
Design and specications are subject to change without notice.
Standby power consumption: 0.5 W
Halogenated ame retardants are not used in the
certain printed wiring boards.
Halogenated ame retardants are not used in cabinets.
(Except for the United States model)