Filter
Top Products
17
CDX-R3310/R30M
2-515-510-11 (1)
H:\Data Disk\2515510111\251551011CDXR3310SU\01US02CD-U.fm masterpage:RightH:\Data Disk\2515510111\251551011CDXR3310SU\01US02CD-U.fm masterpage:Right
No beep sound.
• The beep sound is canceled (page 10).
• An optional power amplifier is connected and
you are not using the built-in amplifier.
The contents of the memory have been
erased.
• The RESET button has been pressed.
tStore again into the memory.
• The power connecting lead or battery has been
disconnected.
• The power connecting lead is not connected
properly.
Stored stations and correct time are erased.
The fuse has blown.
Makes noise when the position of the
ignition key is switched.
The leads are not matched correctly with the
car’s accessory power connector.
The display disappears from/does not
appear in the display window.
• The dimmer is set “DIM-ON” (page 10).
• The display disappears if you press and hold
(OFF).
tPress and hold (OFF) again until the
display appears.
• The connectors are dirty (page 15).
CD/MD playback
The disc is automatically ejected.
The disc has trouble.
tCheck the following:
The disc cannot be loaded.
• Another disc is already loaded.
• The disc has been forcibly inserted upside
down or in the wrong way.
The disc does not playback.
• Defective or dirty disc.
• The CD-Rs/CD-RWs are not for audio use
(page 13).
MP3 files cannot be played back.
The disc is incompatible with the MP3 format
and version (page 13).
MP3 files take longer to play back than
others.
The following discs take a longer time to start
playback.
–a disc recorded with a complicated tree
structure.
–a disc recorded in Multi Session.
–a disc to which data can be added.
The ATRAC CD cannot play.
• The disc is not created by authorized software,
such as SonicStage or SonicStage Simple
Burner.
• Tracks that are not included in the group cannot
be played.
The display items do not scroll.
• For discs with very many characters, those may
not scroll.
• “A.SCRL” is set to off.
tSet “A.SCRL-ON” (page 10) or press
(SCRL).
The sound skips.
• Installation is not correct.
tInstall the unit at an angle of less than
45° in a sturdy part of the car.
• Defective or dirty disc.
The operation buttons do not function.
The disc will not eject.
Press the RESET button (page 4).
Radio reception
The stations cannot be received.
The sound is hampered by noises.
• Connect a power antenna control lead (blue) or
accessory power supply lead (red) to the power
supply lead of a car’s antenna booster (only
when your car has built-in FM/AM antenna in
the rear/side glass).
• Check the connection of the car antenna.
• The auto antenna will not go up.
tCheck the connection of the power antenna
control lead.
• Check the frequency.
Preset tuning is not possible.
• Store the correct frequency in the memory.
• The broadcast signal is too weak.
Automatic tuning is not possible.
• Setting of the local seek mode is not correct.
tTuning stops too frequently:
Press (SENS) until “LOCAL-ON” appears.
tTuning does not stop at a station:
Press (SENS) repeatedly until “MONO-
ON” or “MONO-OFF” (FM), or “LOCAL-
OFF” (AM) appears.
• The broadcast signal is too weak.
tPerform manual tuning.
During FM reception, the “ST” indication
flashes.
• Tune in the frequency accurately.
• The broadcast signal is too weak.
tPress (SENS) to set the monaural reception
mode to “MONO-ON.”
An FM program broadcast in stereo is heard
in monaural.
The unit is in monaural reception mode.
tPress (SENS ) “MONO-OFF” appears.
continue to next page t