Filter
Top Products
3
SONANCE VISUAL PERFORMANCE
®
6” IN-WALL
NOTE
: ADJUSTING THE TENSION OF THE ROTOLOCK CLAMPS
SO THAT THE SPEAKER FRAME IS FLAT WILL HELP ENSURE THAT
THE GRILLE CONTACTS THE WALL ALL THE WAY AROUND THE
SPEAKER FOR A PROPER FIT.
6. The new micro flange grille is held in place by several small,
powerful magnets on the speaker frame. Place the grille
against the speaker and the magnets will hold it firmly in
place. When properly installed, the grille flange should make
contact with the wall all the way around the speaker.
Painting The Grilles
See the accompanying
Painting Instructions
sheet for painting
instructions.
Speaker Adjustments
Pivoting Tweeter
All Visual Performance Series 6” in-wall speakers have a pivot-
ing tweeter that allows you to direct sound towards or away from
the listening area, depending on how the speakers are being
used:
• If you’re using the speakers in stereo or as the front left/center/
right speakers in a home theater, pivot the tweeter directly
towards the listening area. This will help the sound from the
speakers blend into a solid soundstage even if the speakers are
widely separated.
• If you’re using the speakers as surround channel speakers in a
home theater, you can create a more diffuse, spacious sur-
round effect by pivoting the tweeter towards a wall or
window, away from the listeners.
To Pivot the Tweeter:
Apply light pressure to the
plastic ring around the out-
side edge of the tweeter
dome, as shown in
Figure 9
.
Take care not to touch or
apply pressure to the tweeter
dome itself.
Specifications
VP69
Tweeter: 1" (25mmBeryllium dome, Ferrofluid-
cooled, pivoting, in acoustic back
chamber
Woofer: 6½" (165mm) Beryllium cone with a
rubber surround, extended pole piece
Frequency Response: 40Hz – 20kHz ±3dB
Impedance: 6 ohms nominal; 4 ohms minimum
Power Handling: 5 watts minimum; 150 watts maximum
Sensitivity: 90dB SPL (2.83V/1 meter)
Grille Material: Perforated Steel
Dimensions (W x H x D): 7¾" x 11
5
/
8" x 3½”
(197mm x 295mm x 89mm)
Cutout Dimensions (W x H): 6
7
/
8” x 10¾" (175mm x 273mm)
Shipping Weight: 12 lbs (5.45kg) pair
VP67
Tweeter: 1" (25mm) Aluminum dome,
Ferrofluid-cooled, pivoting, in
acoustic back chamber
Woofer: 6½" (165mm) Coated carbon fiber
cone with a rubber surround, extended
pole piece
Frequency Response: 43Hz – 20kHz ±3dB
Impedance: 6 ohms nominal; 4 ohms minimum
Power Handling: 5 watts minimum; 140 watts maximum
Sensitivity: 90dB SPL (2.83V/1 meter)
Grille Material: Perforated Steel
Dimensions (W x H x D): 7¾" x 11
5
/
8" x 3½”
(197mm x 295mm x 89mm)
Cutout Dimensions (W x H): 6
7
/
8
” x 10¾" (175mm x 273mm)
Shipping Weight: 11 lbs (5.0kg) pair
VP65/VP65TL
Tweeter: 1" (25mm) Silk dome, Ferrofluid-
cooled, pivoting, in acoustic back
chamber
Woofer: 6½" (165mm) Carbon fiber cone with
a rubber surround
Frequency Response: 44Hz – 20kHz ±3dB
Impedance: 8 ohms nominal; 6 ohms minimum
Power Handling: 5 watts minimum; 130 watts maximum
Sensitivity: 90dB SPL (2.83V/1 meter)
Grille Material: Perforated Steel
Dimensions
VP65 (W x H x D): 7¾" x 11
5
/
8
" x 3½”
(197mm x 295mm x 89mm)
VP65TL (W x H x D): 8¼" x 12
3
/16" x 2½”
(210mm x 310mm x 65mm)
Cutout Dimensions (W x H): 6
7
/
8” x 10¾" (175mm x 273mm)
Shipping Weight: 10 lbs (4.5kg) pair
FIGURE 9: PIVOTING THE TWEETER