Filter
Top Products
SOUND ADVANCE
SA
R
212 Avenida Fabricante, San Clemente, CA 92672
TEL 800-592-4644 / 949-492-7777 • FAX 949-361-5151 • www.soundadvance.com
Recommended Installations:
• 9/16" T-bar suspended ceiling systems
• 15/16" T-bar suspended ceiling systems
Recommended Environment:
• Indoor or weather-protected outdoor
Recommended Accessories:
• PBB 2.0 Backbox kit (23-3/4" x 23-3/4" x 5";
603mm x 603mm x 127mm)
• ECS2432D Enclosure compensation module
• Safety Strap (secures SpeakerTile to backbox)
Available Models:
ST2432D: Plain white (shown in photo)
ST2432D-3D1: Fine Fissured
®
(or similar) tile pattern
ST2432D-3D2: Cortega
®
(or similar) tile pattern
ST2432D-3D4: Fissured
®
(or similar) tile pattern
ST2432D-3D7: Optima
®
/Ultima
®
(or similar) tile pattern
ST2432D-3D21: Cirrus
®
(or similar) tile pattern
Tegular cuts are available to match tegular ceiling tiles on 15/16" T-bar
grids. Tegular cuts are not required to match tegular ceiling tiles on 9/16"
T-bar grids. (See below for ceiling tile examples.) Call Sound Advance
for details.
Performance Specifications:
Radiating Surface: 549 in2 (3,540cm2) Planar Diaphragm
Tweeter System: 0.82 lb (0.37kg) Magnet with 1.02" (26mm)
voice coil; 1,200Hz, 12dB/octave high-pass crossover
Woofer System: 0.82 lb (0.37kg) Magnet with 1.02" (26mm)
voice coil; 1,200Hz, 12dB/octave low-pass crossover
Frequency Response: 40Hz – 19kHz ±4dB
Power Rating: 75 Watts RMS as per EIA standard RS-426-A
Pressure Sensitivity: 92dB, 1W/1m
System Impedance: 8 ohms nominal, 5.5 ohms minimum
Transformer: Primary Voltage — 70.7 Volts
Primary Taps — 0.5, 1, 2, 4, 8, 16, 32 Watts; 8-ohm bypass
Dimensions (H x W x D): 23-7/16" x 23-7/16" x 3"
(595mm x 595mm x 76mm)
Product Weight: 11.0 lbs (5kg) each
Shipping Weight: 15.5 lbs (7kg) each
Warranty:
Sound Advance warrantees the ST2432D to be free of any defect in
materials or workmanship for a period of 5 years from the date of
purchase. During the warranty period, Sound Advance will repair or
replace (at its option) all such defects without charge for parts or labor,
if returned prepaid to the proper Sound Advance service facility, together
with the original sales receipt or other proof of purchase. The unit will be
returned prepaid.
ST2432D
SpeakerTile
PBB 2.0
Backbox
Ceiling Tile
(used as rear
panel of backbox
T-Bar
Ceiling
Grid
Installation Example:
T-Bar and
Ceiling Tile
Variations
Flush
9
/
16
" Grid
Tegular
9
/
16
" Grid
Tegular
9
/
16
" Grid
Flush
15
/
16
" Grid
Tegular
15
/
16
" Grid
©2007 Sound Advance. All Rights Reserved. Sound Advance, SpeakerTile and Planar Diaphragm Technology are trademarks or registered trademarks of Dana Innovations. Fine Fissured, Cortega, Fissured,
Optima, Ultima and Cirrus are registered trademarks of Armstrong World Industries. Specifications subject to change without notice. For the latest Sound Advance product information please go to
www.soundadvance.com.
The Sound Advance
®
ST2432D SpeakerTile
®
is a remarkable combination of widebandwidth, wide dispersion, and a highly-
refined aesthetic presentation, designed for commercial installations. It is part of a unique family of truly invisible distributed
sound products from Sound Advance. All ST2432D SpeakerTile models are available in several mounting options, allowing
them to be easily installed into standard T-bar suspended ceiling systems, completely replacing a standard 2' x 2' ceiling tile.
The ST2432D is available in six different models, featuring a selection of standard 3-dimensional patterns or factory-applied
surface finishes that allow a match with almost any suspended ceiling tile pattern. The white Expanded PolyStyrene (EPS)
front surface of the speaker tile allows all models to optionally be finished on-site with any water-soluble finish, such as
latex paint, or covered with light wallpaper, fabrics and selected texture coats,* further enhancing the SpeakerTile’s ability to
blend invisibly with almost any interior design choice. Patented Planar Diaphragm Technology™ allows a ST2432D that has
been properly installed in a suspended ceiling to radiate sound in a 140° hemispherical pattern with smooth, even coverage.
This dispersion characteristic allows ST2432D speakers to be spaced farther apart than narrow-dispersion conventional
speakers, reducing the total quantity of loudspeakers required in almost any installation.
The ST2432D is a two-way, full-range device that utilizes a crossover centered at 1,200Hz, with 12dB per octave slopes for
both low-pass and high-pass sections. The ST2432D is transformer-coupled, with the following input taps: 0.5W, 1W, 2W,
4W, 8W, 16W, 32W and 8-ohm bypass. An optional PBB 2.0 backbox is available, and is recommended for use when the
SpeakerTile is installed in air handling spaces. An optional ECS enclosure compensation module is available, to optimize
performance when the ST2432D is used with the PBB 2.0.
*Please contact Sound Advance for advice before applying any textured coating, light wallpaper or fabrics to the ST2432D.