Sonance BPS-1 Speaker User Manual


  Open as PDF
of 2
 
BPS-1 BANDPASS SUBWOOFER
BPS-1 Specifi cations
Woofer: 8” (203mm) long-throw felted
paper cone with a rubber
surround
Frequency Response: 35Hz – 150Hz ±3dB
Enclosure Dimensions: 9” x 11” x 39½”
(W x H x D) (229mm x 279mm x 1283mm)
Port Tube Length: 15” (381mm)
Minimum Mounting Area: 9
1
/
8
” x 11” x 53¼”
(W x H x D) (232mm x 279mm x 1352mm)
Shipping Weight: 46 lbs (20.9kg) each
SONANCE BPS-1 BANDPASS SUBWOOFER
The Sonance Architectural Series
®
BPS-1 Bandpass Subwoofer system will add deep, powerful bass impact to any audio system.
The
BPS-1 cabinet remains completely hidden from view, delivering its bass energy through Sonance Architectural Series
brackets and an architectural fi nish component that is a discreet complement to the surrounding architectural space.
Features
• Delivers powerful, room-fi lling bass through a small grille that complements the room’s architectural design.
• Trimless and truly fl ush-mount installation — the plane of the subwoofer grille is perfectly aligned with the plane of the ceiling.
• Required Bandpass Connectors allow the BPS-1 to be used with any size round or square Architectural Series bracket to match other Architectural
Series speakers in the space. The Bandpass Connectors are heavily fl ared to minimize port noise during high-volume passages.
• Engineered to provide years of reliable high-power operation, the BPS-1 features a woofer with a felted paper cone with a rubber surround. The
required Sonamp
®
A150 is designed to protect the speaker from damage. This ensures the BPS-1 can be installed in a location that will have limited
or no access without the need for maintenance.
• The very effi cient 4th-order bandpass enclosure produces high output over the subwoofer’s entire frequency range.
• The BPS-1 can be used with any separately-available Architectural Series round and square fi nish component: metal (with or without trim) or cloth
(with or without trim).
Sonance
212 Avenida Fabricante
San Clemente, CA 92672-7531 USA
1.800.582.7777
sonance.com
©2008 Sonance, All Rights Reserved. Sonance, Sonance Architectural Series, and Sonamp are registered trademarks of Dana Innovations.
Due to continuous product improvement, all features and specifications are subject to change without notice. For the latest Sonance product information, go to : www.sonance.com
SONAMP A150 AMPLIFIER (required, available separately)
• Sonamp A150 power amplifi er delivers 150 watts of power to up to two BPS-1 subwoofers and provides fl exible connections that integrate the
BPS-1 into any audio system.
• A built-in limiter prevents overdriving the BPS-1’s woofer driver, even when using a single Sonamp A150 to drive two BPS-1 subwoofer cabinets.
• The A150’s front-panel amplifi er controls (volume, crossover frequency, and phase) let you fi ne-tune the BPS-1’s performance to match a variety of listening
environments and personal preferences.
Sonamp A150 Specifi cations
Maximum Continuous RMS Power
at Clipping: 90 watts
Power Output (Program): 150 watts
Signal-to-Noise Ratio: –95dB
Auto-On Trigger Sensitivity: 10mV
Low-Pass Crossover Frequency: 40Hz ~ 150Hz (variable),
(Bypass Switch OFF) 12dB/octave
Low-Pass Crossover Frequency: 150Hz (fi xed), 12dB/octave
(Bypass Switch ON)
Hi Level Out Hi-Pass Filter: –3dB @ 200Hz, 6dB/octave
Line Level Out Hi-Pass Filter: –3dB @ 150Hz, 6dB/octave
Controls: Variable crossover frequency, variable
output level, Phase switch, Bypass
switch
Power Consumption: 13w (idle); 160w (max power)
Dimensions (W x H x D): 16¾” x 4” x 13½”
(425mm x 102mm x 343mm)
Shipping Weight: 20 lbs (9.1kg) each
GAP
2 X 10
JOIST
9-1/8”
(232mm)
MINIMUM
MOUNTING
HEIGHT
GYPSUM
WALL BOARD
11” (279mm)
1/8” (3mm)
39-1/2” (1003mm)
15” (381mm)
53-1/4” (1353mm)
Minimum Mounting
Area Dimensions
33-5164
 previous