Filter
Top Products
E-6
General control
Press the ON/STAND-BY button to turn the power on.
To dim the display brightness, press the DEMO/DIMMER
button on the remote control.
If you turn off and on the main unit with the volume set to 27
or higher, the volume starts at 16 and fades in to the last set
level.
Turn the volume knob towards VOLUME +/– (on main unit) or
press VOL +/– (on remote control) to increase or decrease the
volume.
When you press any of the following buttons, the unit turns on.
●
iPod, CD, USB, AUDIO / LINE (INPUT), TUNER on the
remote control: Selected function is activated.
●
/ button on the main unit: The unit turns on and play-
back of the last function will start (CD, TUNER, USB, iPod,
AUDIO IN, LINE IN)
The main unit will enter the stand-by mode (when iPod or
iPhone is not docked) after 15 minutes of inactivity during:
iPod or iPhone: No connection.
CD / USB: In the stop mode.
AUDIO IN / LINE IN: No detection of input signal or very low
sound audibility.
Note:
However, if iPod or iPhone is docked, the unit will begin
charging. “Charge Mode” will be displayed.
The volume is muted temporarily when pressing the button
on the remote control. Press again to restore the volume.
When the power is first turned on, the unit will enter the extra
bass mode which emphasises the bass frequencies, and
“X-BASS ON” will appear. To cancel the extra bass mode,
press the X-BASS button on the remote control.
1
Press the BASS/TREBLE button to select “Bass”.
2
Within 5 seconds, press the VOLUME (+ or –) button to
adjust the bass.
1
Press the BASS/TREBLE button to select “Treble”.
2
Within 5 seconds, press the VOLUME (+ or –) button to
adjust the treble.
When the FUNCTION button on main unit is pressed, the
current function will change to different mode. Press the
FUNCTION button repeatedly to select desired function.
Note:
The backup function will protect the memorised function
mode for a few hours should there be a power failure or the
AC power lead becomes disconnected.
Setting the clock (
Remote
control only)
In this example, the clock is set for the 24-hour (0:00) display.
■ To turn the power on
After use:
Press the ON/STAND-BY button to enter the power stand-
by mode.
■ Display brightness control
■ Volume auto fade-in
■ Volume control
■ Auto power on function
■ Auto power off function
■ Muting
■ X-Bass control
CD/USB
RDS
Dimmer 1
Dimmer 2
Dimmer off
(Display is dim).
(Display is bright).
(Display gets dimmer).
■ Bass control
■ Treble control
■ Function
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the ENTER button. To adjust
the day, press the or button and then press the
ENTER button.
4
Press the or button to select 24-hour or 12-hour
display and then press the ENTER button.
The 24-hour display will appear.
(0:00 - 23:59)
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
5 To adjust the hour, press the or button and then
press the ENTER button. Press the or button
once to advance the time by 1 hour. Hold it down to
advance continuously.
- 5 ↔ - 4
........
↔ + 4 ↔ + 5
- 5 ↔ - 4
........
↔ + 4 ↔ + 5
FM STEREO
FM MONO
USB
iPod
Audio In
Line In
CD
CD/USB
RDS