Filter
Top Products
HK
TIMER/
SLEEP Timer set indicator
POWER
ON/
STAND-BY
MEMORY/
SET
TUNING/
TIME
( )
CD
TUNER
(BAND)
VIDEO/
AUX
TAPE
(1 2)
<P=001>
HOW TO USE THE BUILT-IN TIMER
3
4
5
■ Timer recording
1 Press the ON/STAND-BY button to turn the power on.
● Load a cassette for recording into the TAPE 2 cassette com-
partment.
2 Press the TUNER (BAND) or VIDEO/AUX button to select the
desired function.
3 Press the TIMER/SLEEP button repeatedly until a red " " is
displayed.
● The timer set indicator will flash.
4 Press the TUNING/TIME ( or ) button to set the hour start
time, then press the MEMORY/SET button.
5 Press the TUNING/TIME ( or ) button to set the minute
start time, then press the MEMORY/SET button.
● The power will be automatically turned off, and the timer set
indicator will light up.
6 When the preset time is reached, the timer recording will start.
● The volume will increase gradually until it reaches the volume
you were listening to before turning off the unit.
7 When the recording tape reaches its end, the timer recording
will end, and the power will be turned off.
To cancel timer operation:
Press the ON/STAND-BY button to turn the power on.
To change the programmed contents:
Start again from step 1.
Note:
● Once the time is set, the setting will be retained until a new
time is entered.
■ Sleep operation
The radio, compact disc and cassette deck can all be turned off
automatically.
1 Play back the desired sound source.
2 Press the TIMER/SLEEP button repeatedly until "SLEEP" is
displayed.
To change the sleep time:
While the sleep time is displayed, press the TUNING/TIME (
or ) button to adjust the time.
(Maximum: 3 hours - Minimum: 1 minute)
The amount of sleep time can also be changed during the sleep
operation.
● 3 hours - 5 minutes → 5-minute intervals
● 5 minutes - 1 minute → 1-minute intervals
3 Press the MEMORY/SET button.
4 The unit will turn off automatically after the preset sleep time
has elapsed.
Note:
● Once the sleep time is set, it will remain the same duration
until the setting is changed.
To confirm the remaining sleep time:
Press the TIMER/SLEEP button.
To cancel the sleep operation:
Press the ON/STAND-BY button to enter the stand-by mode.
■ Timer playback
1 Press the ON/STAND-BY button to turn the power
on.
2 Press the CD, TUNER (BAND), TAPE (1 2) or
VIDEO/AUX button to select the desired function.
3 Press the TIMER/SLEEP button repeatedly until a
white " " is displayed.
● The timer set indicator will flash.
4 Press the TUNING/TIME ( or ) button to set the
hour start time, then press the MEMORY/SET but-
ton.
5 Press the TUNING/TIME ( or ) button to set the
minute start time, then press the MEMORY/SET but-
ton.
● The power will be automatically turned off, and the
timer set indicator will light up.
6 When the preset time is reached, the volume will
increase gradually until it reaches the volume you
were listening to before turning off the unit.
7 If you select CD or TAPE, the power will be turned
off after the tape or CD is finished playing back.
If you select TUNER or VIDEO/AUX, the power will
be turned off one hour later.
Note:
● When performing timer playback using an external
unit connected to the VIDEO/AUX jacks, only the
power of the main unit will be turned off automat-
ically. (The power of the external unit will not be
turned off.)
● Before setting the timer, make sure that the clock
setting is correct. (Page 6)
(Main unit operation)
CD-BA150(SEC) TINSE0279AWZZ
14